U/L Inner Boom Weld'T-3014

Miller 2" Wheel Lift L-Arm - Century, Champion, Challenger and Vulcan Carriers

This zinc-plated slide-in L-Arm fits the wheel lifts on various models of Century, Holmes and Challenger wreckers and Century, Champion, Challenger and Vulcan car carriers.

$209.99

Miller Crossbar Fork Adapter Offset Fork Holder

These Low Profile Fork Holders are designed to fit a 5" x 5" or 4" x 4" crossbar. They are made from the same special cast alloy material as the other Miller products.

$752.99 – $1,157.99

All-Grip Replacement Hook Latch

This is a replacement latch for All-Grip hooks. Be sure to check below for which one fits your hook.

$3.99 – $45.99

Miller Pin Weldment, Crossbar Pivot, Century and Vulcan

The Crossbar Pivot Pin Weldment from Miller Industries is used on the Underlift Assembly of Century 3212, Vulcan V30 and Holmes 600R Wreckers. This Pin has actually replaced part number 3012-801100, which was used on the Century 3212 and Vulcan V30 Wreckers. Please see the brochure tab for breakdown schematics.

$237.99

Century Wheel Lift Inner Tube Wear Pad 6" x 1.5" Holmes and Vulcan

This is a nylatron wear pad by Miller Industries. It measures 6" x 1-1/2" x 3/8". It will fit the following wreckers: Century Modular Express 300 Series, Modular Midnight Express, Modular 211, Modular 400 & 600 Series, Holmes 440SL, 600R, Vulcan Modular 804, Modular 806, Modular 807, 812 Intruder, Modular 880/890, and 896/897. See Features for related parts and Brochures for reference charts.

$10.59

Miller Crossbar Fabricated

$2,203.99

Washer, Flat, 3/8"

This General Purpose Flat Washer can be used on most Miller Carrier and Wrecker assemblies, including Century, Challenger, Champion, Eagles, Holmes, and Vulcan. Flat washers are typically used under the head of a bolt of nut to distribute the forces applied when tightening. The zinc plating greatly decreases the corrosion rate. Please refer to the Parts Schematics page for lists of breakdowns. This part can be used to replace Part Number 12-0400480.

$0.09

WASHER, HEAVY LOCK 3/8

This part can be used to replace Part Number, 12-0400482.

$0.19

Fastenal 1/4" - 28 Grease Fitting w/ Ball Check

This straight grease fitting is used to dispense grease into a mating part using a grease gun. It is made from steel with a zinc finish and comes with a ball check. This part has replaced part number

$0.29

Century 3212 Holmes 60R and Vulcan V30 Wreckers Crossbar Die Spring Spacer

Miller Industreis crossbar die spring spacer for HD wreckers. Click on the brochure tab to see the part schematic of this item.

$10.59

Crossbar Positioning Plate, For Century 3212,Holmes 600R and Vulcan V30 Wreckers

This crossbar positioning plate fits Century 3212, Holmes 600R and Vulcan V30 heavy duty wreckers.

$50.99

Miller Detent Spring

This Detent Spring from Miller Industries is used in the assembly of crossbars, outer crosstubes, underlifts, wheel lifts, and crossbeams of many different car carriers and wreckers. These include Century, Holmes, and Vulcan Wreckers, as well as, a Vulcan Car Carrier. See the brochures tab for a complete list and part breakdowns.

$23.99

Miller 1" Chrome Ball

This 1" Chrome Ball from Miller Industries is used on many assembly applications, including crossbar, outer crosstube, underlift, wheel lift, and crossbeam assembly. These assemblies are for Century, Holmes, and Vulcan Car Carriers, as well as Vulcan Wreckers. See the brochure tab for a full list of assemblies and part schematics.

$14.69

Miller Retaining Ring, 1-1/2"

This 1-1/2" Retaining Ring from Miller Industries is used on many different assemblies including boom, Subframe, recovery boom, wheel lift boom, underlift, dual and single winch extendable boom, and dual and single winch non-extendable boom assemblies. These assemblies can be found on many Century, Challenger, Champion, Eagle, Holmes, and Vulcan Wreckers. See the brochures tab for a full list of assemblies and part schematics.

$7.49

Miller Weldless Chain Link 5/8" Used w/ Cable Tie Back

This welded link is commonly used in conjunction with the cable tie-back springs on Miller Century, Vulcan and Challenger Heavy Duty Wreckers See part numbers:

$20.49

Miller 5/8" Flat Washer - Vulcan 896 LD Wrecker Wheel Grids Bracket

This 5/8" flat washer from Miller Industries fits the L-Arm receiver bracket on Vulcan 896 light-duty wrecker wheel grids. This washer is installed with the 5/8" bolt on the bottom side of the pivot arm. An L-Arm is also known as a scoop, wheel retainer and tire restraint.

$8.89