Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
These are Continuous Wire Harness Rolls, by Maxxima. These Harnesses come with
various connects an different length leads. These light harness leads are sold
as each. Enter the number of leads into the quantity field then add to your
cart.
Grand General 0.180 diameter female double bullet
receptacle wiring harnesses with 4 inch spacing per plug and designed for use
with 0.180 diameter male bullet plugs on most lights. These plugs are made of
18-Ga UL listed wire with one black and one white wire and have specially
designed rounded prong tips for easy installation and help to secure the
connection.
Keeps water, salt and other corrosives from LED lamps. 8" 16 gauge GPT wire;
tin plated brass terminals. Stripped end and ring terminal Fit 'N Forget S.S.
plug.
Keeps water, salt and other corrosives from LED lamps. Combine with LED lamps
for Lifetime Lighting Warranty eligibility. 5" 16 gauge GPT wire with tin
plated brass bullets/receptacles. Built as a Fit 'N Forget M/C .180 bullet
terminal plug.
This three-prong, right angle clip pigtail provides power connection for sealed
lights, specifically combination stop, turn and tail lights. The red and black
lead wires are bare for making power connection. Red is turn signal, and black
is tail signal. The white ground wire has #10 ring terminal at the end.
These are Continuous Wire Harness Rolls, by Maxxima. These Harnesses come with
various connects an different length leads. These light harness leads are sold
as each. Enter the number of leads into the quantity field then add to your
cart.
Power Up Products resistor load kit produces the same draw as an incandescent
lamp. Set to flash at a rate determined by the direct current drawn by the
lamp load. Flashes at a rapid rate to indicate the burned out lamp. Each
resistor is rated to 30 watts. Mounting brackets included.
3-Pin Load Equalizer by Maxxima. When replacing an incandescent turn signal or
other flashing light with an LED light, the amp draw of the LED light is so low
that sometimes it will flash too slow or too fast, or not flash at all. This
load equalizer will level out the amp draw with the flasher module to allow the
LED light to flash at the correct speed.
Grand General 0.180 diameter female double bullet
receptacle wiring harnesses with 4 inch spacing per plug and designed for use
with 0.180 diameter male bullet plugs on most lights. These plugs are made of
18-Ga UL listed wire with one black and one white wire and have specially
designed rounded prong tips for easy installation and help to secure the
connection.
Keeps water, salt and other corrosives from LED lamps. 8" 16 gauge GPT wire;
tin plated brass terminals. Stripped end and ring terminal Fit 'N Forget S.S.
plug.
Keeps water, salt and other corrosives from LED lamps. Combine with LED lamps
for Lifetime Lighting Warranty eligibility. 5" 16 gauge GPT wire with tin
plated brass bullets/receptacles. Built as a Fit 'N Forget M/C .180 bullet
terminal plug.
This three-prong, right angle clip pigtail provides power connection for sealed
lights, specifically combination stop, turn and tail lights. The red and black
lead wires are bare for making power connection. Red is turn signal, and black
is tail signal. The white ground wire has #10 ring terminal at the end.
These are Continuous Wire Harness Rolls, by Maxxima. These Harnesses come with
various connects an different length leads. These light harness leads are sold
as each. Enter the number of leads into the quantity field then add to your
cart.
Power Up Products resistor load kit produces the same draw as an incandescent
lamp. Set to flash at a rate determined by the direct current drawn by the
lamp load. Flashes at a rapid rate to indicate the burned out lamp. Each
resistor is rated to 30 watts. Mounting brackets included.
3-Pin Load Equalizer by Maxxima. When replacing an incandescent turn signal or
other flashing light with an LED light, the amp draw of the LED light is so low
that sometimes it will flash too slow or too fast, or not flash at all. This
load equalizer will level out the amp draw with the flasher module to allow the
LED light to flash at the correct speed.