Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
This fire retardant trim from Lavanture Products Co. is a flexible trim with
metal clips to provide a permanent grip. It is manufactured out of a
thermoplastic Vulcanizate (TPV) material formulated to pas the National Fire
Protection Agency (NFPA) standards. This material also complies with the UL
94HB flame requirements most commonly needed in electrical enclosure
applications.
These stainless steel screws are used with 7/8" stanchions. They measure 10/32" x 3/4", which is the correct size for low-profile handrail stanchions. These screws will maintain a clear, rust free appearance.
These Hi-Amp Circuit Breakers are ideal for cranes, dump hoists, lift gates,
plows, spreaders, switch panels and power distribution panels. Choose from 50,
80, 100, or 150 Amp Circuit Breakers. These circuit breakers double as a master
disconnect as well. In the event of a "short circuit" the circuit breaker will
"trip" to the off position. Unlike an automatic reset, the manual version stays
open until it is manually reset. By pushing the reset button you can also
disconnect the entire system. This is extremely helpful when servicing the
electrical system.
Buyers Products 5 Inch Incandescent Flood Light has a sealed rubber housing and
a blunt cut connection. It sits on a zinc-plated mount and has a 10 in. lead
length. The 35W light is IP67 rated for water and dust resistance.
Temflex vinyl insulating electrical tape. It is flame retardant, lead free,
cold and sunlight resistant, suitable for use at not more than 600V and not
more than 80?C (176?F).
Howes Lubricator heavy-duty, multi-purpose Lubricator and Penetrating Oil is guaranteed to loosen rusted nuts and bolts. The lubricant can be sprayed on wires, leads and distributor caps and is safe to use on almost any surface.
Phoenix electrical junction blocks are high-quality, easy-to-use terminal
blocks that allow you to connect multiple electrical sources in your car,
truck, trailer, or RV. They feature a two-piece design and are available with a
range of poles to accommodate a variety of wiring requirements. These blocks
ensure that your wires stay in place and don't contact other leads, keeping all
of your electrical devices organized and safe from short circuiting.
Our popular SL-9 magnetic tow light kit comes with two sealed beam truck lights
in a rubber housing, plastic-housed magnets, and 30' of 4 - wire cable all
pre-wired into the male plug. The kit also includes a plastic carrying case
and the female plug. The flexible cable is 16 gauge wire with "Yukon Weather
Proven" outer and inner jackets.
Mississippi Welders depressed center fast grinding wheel. It has an aluminum oxide grain with a soft bond for fast shock removal. It is used for ferrous metals (iron, steel, welds, etc.) and low grade stainless steel.
Premium quality primary wire cable manufactured to meet or exceed ATA
specifications. Color coded PVC cover resists weather and protects the
individual color coded, annealed copper conductor strands. Commonly used to
install or repair marker/ID light circuits.
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This is a decal kit for the wheel lift operations on a Vulcan 880/890 Series by Miller Industries. This part can be used to replace Part Numbers: 9033149, 9033150, 9033151, 9033152, 9033153, 9033154, 9033155, and 9033156.
This Pin and Link Assembly from Miller Industries is used on the Control
Components Assembly of Chevron Car Carriers. These include 14, 16, 20 and 30
Series Car Carriers. Please see the features below for a list of trucks and see
the brochure tab for breakdowns.
This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many
different Miller Wrecker assemblies. These assemblies include the boom, wheel
lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes
Wreckers. Please see the brochure for a full list of breakdowns.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is a handle bracket for Gresen V20 Valve. This piece bolts onto the valve
assembly itself and is use to hold the control rod linkage to the valve.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This Composite Bell Crank from Miller Industries is used on the 6 and 9 Spool
Control Station of Century Generation II LCG 16 Series Steel & Aluminum Car
Carriers. These carriers are made in 2014 or later. Please see the brochure tab
for a list of breakdowns.
This Pin and Link Assembly from Miller Industries is used on the Control
Components Assembly of Chevron Car Carriers. These include 14, 16, 20 and 30
Series Car Carriers. Please see the features below for a list of trucks and see
the brochure tab for breakdowns.
This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many
different Miller Wrecker assemblies. These assemblies include the boom, wheel
lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes
Wreckers. Please see the brochure for a full list of breakdowns.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is a handle bracket for Gresen V20 Valve. This piece bolts onto the valve
assembly itself and is use to hold the control rod linkage to the valve.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This Composite Bell Crank from Miller Industries is used on the 6 and 9 Spool
Control Station of Century Generation II LCG 16 Series Steel & Aluminum Car
Carriers. These carriers are made in 2014 or later. Please see the brochure tab
for a list of breakdowns.