Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
The Revolution Boom Head from In The Ditch is a direct replacement for the
Holmes 440, SP8000, SP12000 Side Puller and the Century Midnight Express. This
wire rope guide cover comes off with one hand, allowing for easy wire rope
installation.
This Revolution Boom Head from In The Ditch is a direct replacement for the Holmes 440, SP8000, SP12000 Side Puller, and the Century Midnight Express. The head accepts 3/8" and 7/16" wire rope, and it has a 12,000 lb. rating. The guide cover comes off easily with one hand, which allows the wire rope to be installed with ease.
Available in Classic or Tower's Edge webbing these Low Profile V-Straps have a
15" j-hook attached to the end of each. Use the new Low Profile V-Straps from
B/A to reduce damage to the under carriage of vehicles. By using an oblong link
the hook of the winch line is now in a horizontal plane, with the tip of the
hook pointed away from components that could otherwise be damaged. This reduces
the risk of puncturing the vehicles' oil pan, transmission, valance, bumper,
radiator, etc. All V-Straps are made with reinforced Cordura eyes for maximum
resistance to tears, cuts and abrasions.
Winch Cables can also be known as: winch line, wire rope, wrecker cables, car
carrier cables, and rollback cables. These Fiber Core Winch Cables are made
with Extra Improved Plow Steel, which provides superior strength and
flexibility. When pressure is exerted on the working winch cable, the lubricant
reservoir gives off lubricant to minimize the wear of wire on wire, assuring
longer service life. These winch cables also come with an Alloy Self-Locking
Swivel Hook that will not open when under load, providing a secure, safe
connection. This swivel hook will rotate as it is reeled into the drum so that
it will wrap and lay better.
Zips J-chain assemblies include a 15" J hook on one end of the Grade 70 5/16" chain and a mini J hook and grab hook cluster on the
other end. Choose from four lengths:
This Pin and Link Assembly from Miller Industries is used on the Control
Components Assembly of Chevron Car Carriers. These include 14, 16, 20 and 30
Series Car Carriers. Please see the features below for a list of trucks and see
the brochure tab for breakdowns.
This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many
different Miller Wrecker assemblies. These assemblies include the boom, wheel
lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes
Wreckers. Please see the brochure for a full list of breakdowns.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is a handle bracket for Gresen V20 Valve. This piece bolts onto the valve
assembly itself and is use to hold the control rod linkage to the valve.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This Composite Bell Crank from Miller Industries is used on the 6 and 9 Spool
Control Station of Century Generation II LCG 16 Series Steel & Aluminum Car
Carriers. These carriers are made in 2014 or later. Please see the brochure tab
for a list of breakdowns.
This Pin and Link Assembly from Miller Industries is used on the Control
Components Assembly of Chevron Car Carriers. These include 14, 16, 20 and 30
Series Car Carriers. Please see the features below for a list of trucks and see
the brochure tab for breakdowns.
This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many
different Miller Wrecker assemblies. These assemblies include the boom, wheel
lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes
Wreckers. Please see the brochure for a full list of breakdowns.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is a handle bracket for Gresen V20 Valve. This piece bolts onto the valve
assembly itself and is use to hold the control rod linkage to the valve.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This Composite Bell Crank from Miller Industries is used on the 6 and 9 Spool
Control Station of Century Generation II LCG 16 Series Steel & Aluminum Car
Carriers. These carriers are made in 2014 or later. Please see the brochure tab
for a list of breakdowns.