Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
This Super Oilite Bushing from Miller Industries is used on the Wheel Lift Assembly of Century Formula 6500/600 Series Wreckers, Century Formula I Wheel Lift 411/611 Wreckers and Challenger 4700 Series Wreckers. See the attached brochures. This part can be used to replace Part Numbers: 12-0301583, 12-0301845, 12-0301382, and 12-0302093.
This is a replacement wheel lift upper arm pin weldment on Light Duty Century
and Holmes Wreckers by Miller Industries. This pin attaches the wheel lift
upper arm weldment to the frame weldment. This pin fits the Century Formula
6500, 600 Series and Modular 400 & 600 Series. It will also fit the Holmes HP
552/DFT 650 wrecker. To view the part schematics please click the Brochures
tab.
This is a replacement wheel lift upper arm pin weldment on Light Duty Century
and Holmes Wreckers by Miller Industries. This pin attaches the wheel lift
upper arm weldment to the outer boom weldment of the wheel lift. This pin fits
the Century Formula 6500, 600 Series and Modular 400 & 600 Series. It will also
fit the Holmes HP 552/DFT 650 wrecker. To view the part schematics please click
the Brochures tab.
This is the Lift Cylinder Pin on the Wheel Lift for Century Formula 6500 - 600
Series and Century Modular 400 & 600 Light Duty Wreckers by Miller Industries.
This is the pin for the rod end of the lift cylinder. To view specific models
this pin will fit see Features below. To view part schematics click the
Brochure tab.
This is the weldment pin that connects the outer stinger to the parallel arms
on a Formula I 411/412 by Miller Indstries. See brochure for reference chart.
This is the base lift cylinder pin on the wheel lift of Century, Challenger and
Holmes wreckers by Miller Industries. This pin replaces part number
12-0801012. This cylinder pin will fit the following wreckers: Century Formula
I - Duplex Tilt 411 & 412, Formula I - Duplex Tilt Super Six & 500, Formula
6000 - 600 Series, Formula 6500 - 600 Series, Metro I - Duplex Tilt, Challenger
4700 Series, and the Holmes 440 Series. To view year ranges see Features below.
To view part schematics click on the Brochures tab.
This is a Pin that is used in different locations on the Wheel Lift of Century
Formula I Duplex Tilt 411 & 412, and Holmes 440 Series / DFT 400 light Duty
wreckers by Miller Industries. This pin is used to hold the tilt cylinders on
to the wheel lift frame weldment. This pin also is used to attach the upper arm
weldments to the wheel lift frame weldment also. To view part schematics click
on the Brochure tab.
This is the Wheel Lift Tilt Cylinder Pin for the Holmes 440 Series / DFT 400 light duty wreckers by Miller Industries. This pin goes through the rod end of the cylinder. This pin attaches the tilt cylinder to the outer wheel lift boom. To view the part schematic click on the Brochure tab. This part can be used to replace Part Number 12-0801010.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is the extend cylinder for the wheel lift on Miller Industries Light Duty
Wreckers. This will fit the Century EB4 Express, Century Formula I 411 & 412,
Century Formula I Super Six & 500 Series, Century Formula II, Century Formula
6000 - 600 Series, Century Metro I, Century Modular 211, Century Modular 400 &
600, Century 211 & 212. It will also fit the Challenger 4700 Series, Champion
Model 101, Holmes 440 Series, Vulcan Modular 804, and Vulcan Modular 806. To
view specific years of wrecker models see Features below. To view part
schematics click on the Brochures tab.
Dimensions: 39"L x 5"W x 5"H
Length Eye to Eye: 37.5" L
Fits:
Century EB4 Express (03/1999 to Current)
Century Formula I, Duplex Tilt, 411 & 412 Wreckers
Century Formula I, Duplex Tilt, Super Six & 500 Series
Century Formula II
Century Formula 6000, 600 Series
Century Metro I, Duplex Tilt (D.T.) Wheel Lift System
Hex Head Cap Screws are designed for easy assembly into a tapped hole. This
screw meets SAE specifications with a specially designed washer face under the
head and a chamfered point. The zinc plating slows the corrosion rate making it
last through the elements. This screw is 3/8" diameter x 7/8" long. It is used
on the Wheel Lift Assembly of Champion Carriers prior to 2001, and Vulcan 10
Series Carriers made from 2003-2005. See the features below, and the brochure
tab for a list of breakdowns.
This is the Wheel Lift Tilt Cylinder on Century, Challenger, and Holmes Light
Duty Wreckers. This cylinder will fit Century Formula I Duplex Tilt 411, 412,
Super Six and 500 Series wreckers. It will also fit the Century Formula 6000 -
600 Series, Metro I - Duplex Tilt, Modular 400 and 600 Series. It fits the
Challenger 4700 Series and the Holmes 440 Series. This tilt cylinder can be
used on both the left and the right side of the wheel lift. This cylinder
replaces part numbers: 12-0302905, 12-0302904, 12-0303674, and 12-0303675. To
view specific wrecker models this cylinder fits see Features below. To view
part schematics click the Brochures tab.
This is an inner tube slide pad for the top side of the wheel lift on all
Century, Vulcan, Champion, & Challenger car carriers excluding the LCG Series.
It is also compatible on Vulcan 810 Intruders and Century 411/412 & Midnight
Express. See Features for quantities for each model needed. Each pad sold
separately.
This is the Lift Cylinder on the Wheel Lift of Century Wreckers with the
Formula I and Formula 6500 Wheel Lifts. It is used on the Century Formula 6500
- 600 Series and the Modular 400 & 600 Series with these wheel lift options. To
view part schematics click the Brochure tab.
This is a front stop pin assembly for the scoop bracket weldment on Light Duty Vulcan Wreckers by Miller Industries. This stop pin w
ill fit the following models: Vulcan Modular 804, Modular 806, and Modular 880/890. It works for both sides of the wrecker. This par
t can be used to replace Part Numbers: 8621400 and 880411500.
This is a bronze bushing for an Eagle Best-Lift Forklift Attachment. This bushing is used where the claws of the forklift attachment mounts to the crossbar. You will need two, one for the driver side claw and one for the passenger side claw. The dimensions of this bushing are 3" long with a 1-1/4" outside diameter and a 1" inside diameter. This part can be used to replace Part Number E300002.
Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube from Miller Industries is a complete right hand assembly with cam lock style plunger pins. This cross tube will fit 3.5" x 3.5" square tubes. It is used on the wheel lift and slide-in tire restraint assembly of Century, Champion, and Vulcan Car Carriers. Shop for the left hand version of this Cross Tube,
Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube from Miller Industries is a complete left hand assembly with cam lock style plunger pins. This cross tube will fit 3.5" x 3.5" square tubes. It is used on the wheel lift and slide-in tire restraint assembly of Century, Champion, and Vulcan Car Carriers. Shop for the right hand version of this Cross Tube,
This is a replacement L-arm claw pivot pin weldment used on the wheel lift of
the Century Modular Midnight Express and the Holmes 220 Snatcher and 440SL
light duty wreckers by Miller Industries. This is the pin that allows the L-arm
to pivot on the crossbar which secures the tire of towed vehicle. To view the
part schematics please click on the Brochure tab above.
Note: Special Handling Fees Apply for Specific Items
This alloy pivot-style L-Arm from Miller Industries fits Formula 1 and Formula
6500 wheel lifts on Century 400 and 600 Series and Challenger 4700 and 4800
Series wreckers. Also known as a tire restraint or wheel retainer, this
aluminum L-Arm fits 2" x 3" outer crosstubes and features a scoop style tire
pan. The drivers side part can be used to replace Part Nos.: 12-0803648 and
12-0903489 and the passenger side part can be used to replace Part Nos.:
12-0803649 and 12-0903490.
Option of driver or passenger position
Fits 2" x 3" outer crosstubes
Pivot style receivers
Alloy construction
Scoop style tire pan
4,000-lb. capacity
Driver side (12-0904156) replaces Part Nos.: 12-0803648 and 12-0903489
Passenger side (12-0904157) replaces Part Nos.: 12-0803649 and 12-0903490
This Wheel Grid Assembly from Miller Industries is a right hand assembly that fits 3.5" x 3.5" square tubes. The wheel grid has a Vu
lcan patented strapless system that is used on the Crossbar and Outer Crosstube Assembly of Vulcan 804, 806, 870, and 880 wheel lift
s, as well as Vulcan Car Carriers. This wheel grid accepts L-Arm 8700180. Click here for the left hand version of this wheel grid 8800800.
This zinc-plated slide-in L-Arm fits the wheel lifts on various
models of Century, Holmes and Challenger wreckers and Century, Champion,
Challenger and Vulcan car carriers.
Note: Special Handling Fees Apply for Specific Items
This zinc-plated mild steel L-Arm from Miller Industries fits the Vulcan 10
Series car carriers and 800 Series light-duty wheel lifts with option of driver
or passenger side fit. Sometimes called a tire restraint or wheel retainer, the
2 x 2.5 tube is designed to work with the driver side outer crosstube 8800900.
This strapless system offers a Working Load Limit of 4,000 lbs. This scoop also
features adjustment holes for proper tire fitment and a grated pan for improved
grip.
2 x 2.5 aluminum tube
Opton of driver or passenger positioning
Adjustment holes
Grated scoop tire pan
Use with 8800900 outer crosstube
WLL: 4,000 lbs.
Fits:
2003-Current Vulcan 10 Series Steel & Aluminum Carriers
2001-Current Vulcan 10 Series Extreme Angle Steel Carriers
Replacement pivot lock pin with attachment cable for Century new style "Pivot-L" wheel grids. This part can be used to replace Part Numbers: 12-0714415 and 12-0904140.
Note: Special Handling Fees Apply for Specific Items
This painted steel L-Arm from Miller Industries fits the wheel lifts on various
models of Century, Holmes and Vulcan wreckers. Otherwise known as a tire
restraint or wheel retainer, this L-Arm fits the crosstubes on the driver side.
This part can be used to replace Driver Side Part Nos. 12-00803911 and
12-0803911 & Passenger Side Part Nos.12-00803912 and 12-0803912.
Option of driver or passenger position
Painted steel
Driver side (12-0806978) replaces driver side Part Nos. 12-00803911 and
12-0803911
This is a front stop pin assembly for the scoop bracket weldment on Light Duty Vulcan Wreckers by Miller Industries. This stop pin w
ill fit the following models: Vulcan Modular 804, Modular 806, and Modular 880/890. It works for both sides of the wrecker. This par
t can be used to replace Part Numbers: 8621400 and 880411500.
This is a bronze bushing for an Eagle Best-Lift Forklift Attachment. This bushing is used where the claws of the forklift attachment mounts to the crossbar. You will need two, one for the driver side claw and one for the passenger side claw. The dimensions of this bushing are 3" long with a 1-1/4" outside diameter and a 1" inside diameter. This part can be used to replace Part Number E300002.
Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube from Miller Industries is a complete right hand assembly with cam lock style plunger pins. This cross tube will fit 3.5" x 3.5" square tubes. It is used on the wheel lift and slide-in tire restraint assembly of Century, Champion, and Vulcan Car Carriers. Shop for the left hand version of this Cross Tube,
Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube from Miller Industries is a complete left hand assembly with cam lock style plunger pins. This cross tube will fit 3.5" x 3.5" square tubes. It is used on the wheel lift and slide-in tire restraint assembly of Century, Champion, and Vulcan Car Carriers. Shop for the right hand version of this Cross Tube,
This is a replacement L-arm claw pivot pin weldment used on the wheel lift of
the Century Modular Midnight Express and the Holmes 220 Snatcher and 440SL
light duty wreckers by Miller Industries. This is the pin that allows the L-arm
to pivot on the crossbar which secures the tire of towed vehicle. To view the
part schematics please click on the Brochure tab above.
Note: Special Handling Fees Apply for Specific Items
This alloy pivot-style L-Arm from Miller Industries fits Formula 1 and Formula
6500 wheel lifts on Century 400 and 600 Series and Challenger 4700 and 4800
Series wreckers. Also known as a tire restraint or wheel retainer, this
aluminum L-Arm fits 2" x 3" outer crosstubes and features a scoop style tire
pan. The drivers side part can be used to replace Part Nos.: 12-0803648 and
12-0903489 and the passenger side part can be used to replace Part Nos.:
12-0803649 and 12-0903490.
Option of driver or passenger position
Fits 2" x 3" outer crosstubes
Pivot style receivers
Alloy construction
Scoop style tire pan
4,000-lb. capacity
Driver side (12-0904156) replaces Part Nos.: 12-0803648 and 12-0903489
Passenger side (12-0904157) replaces Part Nos.: 12-0803649 and 12-0903490
This Wheel Grid Assembly from Miller Industries is a right hand assembly that fits 3.5" x 3.5" square tubes. The wheel grid has a Vu
lcan patented strapless system that is used on the Crossbar and Outer Crosstube Assembly of Vulcan 804, 806, 870, and 880 wheel lift
s, as well as Vulcan Car Carriers. This wheel grid accepts L-Arm 8700180. Click here for the left hand version of this wheel grid 8800800.
This zinc-plated slide-in L-Arm fits the wheel lifts on various
models of Century, Holmes and Challenger wreckers and Century, Champion,
Challenger and Vulcan car carriers.
Note: Special Handling Fees Apply for Specific Items
This zinc-plated mild steel L-Arm from Miller Industries fits the Vulcan 10
Series car carriers and 800 Series light-duty wheel lifts with option of driver
or passenger side fit. Sometimes called a tire restraint or wheel retainer, the
2 x 2.5 tube is designed to work with the driver side outer crosstube 8800900.
This strapless system offers a Working Load Limit of 4,000 lbs. This scoop also
features adjustment holes for proper tire fitment and a grated pan for improved
grip.
2 x 2.5 aluminum tube
Opton of driver or passenger positioning
Adjustment holes
Grated scoop tire pan
Use with 8800900 outer crosstube
WLL: 4,000 lbs.
Fits:
2003-Current Vulcan 10 Series Steel & Aluminum Carriers
2001-Current Vulcan 10 Series Extreme Angle Steel Carriers
Replacement pivot lock pin with attachment cable for Century new style "Pivot-L" wheel grids. This part can be used to replace Part Numbers: 12-0714415 and 12-0904140.
Note: Special Handling Fees Apply for Specific Items
This painted steel L-Arm from Miller Industries fits the wheel lifts on various
models of Century, Holmes and Vulcan wreckers. Otherwise known as a tire
restraint or wheel retainer, this L-Arm fits the crosstubes on the driver side.
This part can be used to replace Driver Side Part Nos. 12-00803911 and
12-0803911 & Passenger Side Part Nos.12-00803912 and 12-0803912.
Option of driver or passenger position
Painted steel
Driver side (12-0806978) replaces driver side Part Nos. 12-00803911 and
12-0803911