Miller Industries

Miller Seal / Parker Valve Body

Stop hydraulic leaks with this replacement seal kit for Miller Industries Parker Valve Body. Used on most Miller Industries car carriers and conventional wrecker bodies.

$35.29

Miller LED Side Light

This LED Side Light from Miller Industries is a dual-purpose light that will operate as a marker light and when the docking light function is activated, the light will operate as an LED flood light. It will also function as a marker light and flasher light when used with a Flasher Control Power Unit (not included).

$266.99

Miller Eagle Claw Spring Kit

Spring set for Eagle wheel lifts. This part is used to replace Part Number AWS-1010-A.

$46.99

Miller Return Spring Cap VDP Parker Valves

This cap screws into control valves used by Miller Industries on car carriers. It commonly corrodes from either inside or out. It covers the return to neutral spring mechanism. It is commonly the cause of control lever not moving fully or levers that do not return to their neutral position This part can be used to replace Part Number 9015812.

$82.99

Miller Lenz Hydraulic Replacement Element 10 Microns 25 PSI

This is a replacement filter element for part number 12-0311288 filter assembly and can be used in place of part number 9018309. The filter bypass is in the element. The filtration media in this element is 10 Micron Cellulose with a dirt holding capacity of 11. This element has a 3/4" port size and a 25 PSI bypass. This is the new style filter and will fit the filter assemblies found on Century, Chevron Holmes and Vulcan Wreckers and Car Carriers.

$46.99

Miller Bus Lift Eye Attachment

The 124002634 Lift Eye Attachment is designed for front lifts on many models of the RTS, GMC, and NOVA buses and rear picks on the MCI-9. The rear eye on an MCI ,GL, and GL3 series can be utilized for a rear pick. The eyelet that is bolted on to the jack pad point on many RTS, GMC, and NOVA buses is pinned into the lift eye attachment for a front pick.

$367.99 – $877.99

Miller Fork Spacer Set

Spacers for use with the Century forks from Miller Industries. This attachment was designed to be used when the front axle you are picking up is narrower than the throat of the fork you are using. Simply slide the adapter over one ear of the fork and you have created 1" narrower opening in your fork without having to carry extra attachments in your tow vehicle. Remember to always use safety chains.

$233.99

Miller Bed Lock Pad 10 / 15 Series Prior to 2006

This is a Miller Industries bed lock pad for the Century 10 or 15 series prior to 2005. It has been replaced by a new bed lock weldment 12-0801209.

$43.19

Miller Transport Tie Down Kit

This Transport Tie-Down Kit from Miller Industries comes with all the necessary equipment you need to tie down a load. The kit comes with 5/16" and 3/8" Grade 70 Chains, as well as 1/2" Grade 80 Chains, and two load binders. All of the chains in this kit have a rating tag,

$2,787.99

Miller Keyhole Plate Double Banjo Eye 3/8"

This Keyhole Plate from Miller Industries has a Double Banjo Eye that will provide an additional tie-down point. The keyhole plate can be bolted or welded into place. This plate is 5-7/8" x 7-1/2" x 3/8" thick steel that will accept up to 3/8" chain. This part can be used to replace Part Number 12-0720078. Bare Steel.

$43.19

Miller Short Axle Fork - 5" Wide Opening

This Short 5" Fork from Miller Industries is used to pick up from the leaf spring, axle or frame. These Forks are made from one piece of cast alloy steel that increases the yield strength almost two fold while also making them 30% lighter than the old fork designs. This fork has a 5" wide opening, a 2" diameter shaft and a 3" clearance between the fork holder and the bottom of the fork cutout.

$253.99 – $445.99

Miller 10,000 lb. Underlift Straps

Underlift Tie-Down Straps will give you a secure tie-down and help you avoid damage that is commonly associated with chain straps.

$194.99

Miller Warn Winch 8" Tensioner

OEM Factory Replacement Cable Tensioners. These Cable Tensioners keep constant pressure against your winch drum, which makes your wire rope wind smoother.

$266.99

Miller Medium Axle Fork - 5" Wide Opening

This cast steel alloy Fork from Miller Industries is used to pick up from the leaf spring, axle or frame. Making these forks from one piece of cast steel has increased the yield strength almost two fold while also making them 30% lighter than the old fork designs. This fork has a 5" wide opening, 2" diameter shaft and has a 6-1/4" clearance between the fork holder and the bottom of the fork cutout.

$268.99 – $472.99

Miller Dual Fork Receiver Set

Miller Industries newly redesigned and field-tested dual fork receiver set offers heavy-duty tow operators the advantage of four fork positions on their crossbars, allowing them to achieve the desired clearance and weight distribution on their underlifts during front-pick tows.

$2,499.99 – $4,013.99

Miller LCG Control Light Mounting Bracket

This is a LCG carrier control light mounting bracket from Miller Industries.

$19.09

Miller Flex LED Lamp Kit

This LED Flex Lamp Kit can be used with the rear fenders of a large Century or Vulcan wrecker body.

$168.99

Miller Tall Axle Fork - 5" Wide Opening

Cast Steel Alloy Forks from Miller Industries are used when clearance is needed on a vehicle with a low front end. These forks are made in one piece using a special cast steel process. There is a 5" wide opening at the top of the fork and the shaft has a diameter or 2". There is a 9" clearance between the fork holder and the bottom of the fork cutout. The yield strength has been increased while making them almost 30% lighter than the old fork designs.

$346.99 – $617.99

Miller L-Arm 2" RH / LH w/ Ratchet Strap Century / Champion / Challenger / Vulcan

This L-Arm Assembly from Miller Industries comes with a Ratchet and Strap already bolted on. This assembly can be used on Century, Champion, and Challenger 10 Series Car Carriers, as well as, Vulcan Car Carriers that have slide-in L-Arms. This part can be used to replace Part Number 12-0900776.

$233.99

Miller U-Bolt Lifting Attachment Set

This U-Bolt Lifting Attachment is designed for faster and easier rear hookups on many tractors. The attachment is centered on one of the rear U-bolts on each side and then the underlift is raised. The U-bolt attachment lifts on the bolt saddle while the U-bolt and nut guide it into position. These attachments are designed for Rear Lift Only. 1 Pair Included in Kit.

$628.99

Miller Shackle Hanger Kit

This Shackle Hanger Kit is from Miller Industries. This kit includes 5 shackle hangers.

$261.99

Miller Offset Chain Hook Adapter Version 2 for Dual Fork Holders

Miller Industries has improved the design of its offset chain hook adapter by adding a second pin for stability and reinforcing the chain hook block for additional strength. This updated version now slides into two holes on a heavy-duty fork holder found on 5" x 5" crossbars on Century, Vulcan and Holmes underreaches.

$1,296.99

Miller Light Duty Wrecker Universal Bumper Counter Weight

Miller Industries 400 lbs. Counter Weight. Maximize the tow-ability of your light duty wrecker with this counter weight. Easily mounts on the front of your truck behind the front bumper. This universal counter weight is designed to fit Dodge 3500-5500, Ford F350-F550, and Chevy 3500 Cab Chassis.

$1,540.99

Miller 15,000 lb. Underlift Strap 3"

Underlift Tie-Down Straps will give you a secure tie-down and help you avoid damage that is commonly associated with chain straps. These straps can handle 7,500 lbs. per strap.

$168.99

Miller Spreader Bar Kit Long

Miller Industries Spreader Bar Kit. Miller Industries has developed a new spreader bar to work in conjunction with their full integrated and rotator product lines. Designed for use in all types of heavy and light duty lifting applications, this unique spreader bar allows for executing straight vertical lifts without damaging or collapsing the sides of the casualty.

$4,154.99

Miller Series 10 Gen 2 Roller Bed Lock Assembly

Note: Special Handling Fees Apply

$774.99

Miller Wheel Lift Anchor Spade (FI DFT-400 I-400)

This Miller Industries Wheel Lift Anchor Spade fits Century Formula I, Holmes DFT-400, and Challenger I-400. The wheel lift spade is designed to fit over the outer tube of the wheel lift and use the downward force of the wheel lift to anchor the truck while winching.

$379.99

Miller Universal Fork Holder, 3.5"x4"

Miller offset fork adapter for 3.5" x 4" crossbars. This fork adapter is commonly used on Vulcan V30 Wreckers.

$736.99

Miller Chain Hook Adapter Set

Miller Industries chain hook adapter kit. These chain hook tow bar adapters are specifically designed to fit the cast profile fork holders of Century and Vulcan Heavy Duty Wreckers. They are used when lifting a load when chains are required. For more versatility they may moved back and forth on the crossbar to fit the size of the load being picked up. Sold as a pair.

$1,029.99

Miller Industries 15" Slim LED Light Bar

This light has a clear lens and red led's

$54.99

Miller Heavy Duty Tire Lift Attachment Crossbar

To expand your lifting capabilities your Century can be equipped with the optional wheel lift grid system. This system is available to fit the 4", 5", and 6" crossbars. It is capable of towing vehicles from both the front and rear axles, in either single or dual tire applications. It offers versatility, with a wide range of adjustment for nearly all sizes of tire, as well as axle widths.

$5,141.99 – $5,828.99

Miller DP Winch Half Round 13 3/4" Rub Bar

A 13-3/4" half round rub bar on the tensioner plate for DP winches.

$341.99

Miller King Pin Tow Plate / Trailer Recovery Loop

This King Pin Tow Plate Recovery Loop from Miller Industries was designed to be attached to the fifth-wheel pin on a large trailer so that it can be towed without the presence of a tractor. Slide the plate on to the pin, attach your chains, secure them to your sling and lift. Use your safety chains anytime you are towing for maximum security and safety. This part has replaced part number 124001674.

$319.99

Miller Stainless Steel Fender Flare Century Heavy Duty Wreckers

This stainless steel fenderette from Miller Industries is specifically designed for the Aluminum Body Sides of the Century Heavy Duty Wrecker Line. This fenderette is sold in one dimension and requires trimming to the proper length to fit each individual wheel well. Fits Century Integrated Wrecker Models 4024, 5130, 5230, 7035 and 9055. Also Fits Miller Industries Complete Rotator Models 1135, 1140, 1140RXP, 1150, 1150RXP, 1150R, and 1075S. This stainless steel fenderette also is compatible with Miller Industries Poly Body Line. These will also fit on some front axles of class 8 trucks, but not all. Sold Each.

$485.99

Miller Lock Cylinder and Key Tm700 Type2 Cam

$13.19

Miller Volvo Axle Fork Set - 8" Wide Opening

Miller Industries Specially designed for lifting the Hendrickson Airtek/Steertek front axle is the hollow beam lifting fork. Special care must be taken when lifting the air suspension hollow beam front axles currently being used on many of the Volvo VNT and Freightliner Century Tractors making this fork or a front tire lift a must.

$817.99

Miller Pivot-Style L-Arm Receiver Bracket - Vulcan 870

Option of driver or passenger side pivot-style l-arm receiver bracket from Miller Industries attackes to the outer crosstubes on Vulcan 870 Series light-duty wrecker wheel lift assebmlies. Also known as a wheel retainer and tire restraint, the L-Arm slides into the angled opening, and the desired position is secured with the bottom side locking pin. This scoop bracket weldment includes the swivel locking pin and the comfort grip stop pin.

$540.99

NRC Adjustable Spreader Bar

This short spreader bar is easy enough for one guy to handle and set up. It comes with 3 sections that are rated for 60,000 lbs. at 7'6" at 60 degrees. At full extension, 12'4", they are rated for 35,200 lbs. at 60 degrees. Size of holes are 1 1/2"

$1,899.99

Miller 38" Aluminum Heavy Duty Pylon w/ Lights

38" Extreme 3" Aluminum Aero Dynamic Pylon. Does Not Include Wrapper or Whelen H700 LED Side Lights. This pylon does include 3 marker lights and 2 stop tail turn lights.

$4,548.99

Miller Keyhole Plate Banjo Eye 3/8" Weld In

Banjo Eyes provide Additional Tie Down Points

$26.39

Miller Flex 8 Remote

Special Order, Need receiver Picture for proper programming for purchase order to sync to customers truck.

$1,986.99

Miller Vulcan V-30 Fork Holder 3.5" X 4" Universal

These fork holders are designed to fit a 3.5" x 4" crossbar. They are a universal style fork holder and are commonly used with the Vulcan V-30 Medium Duty Wreckers.

$1,200.99

Miller LED Strip Lighting

This light has been the standard toolbox lighting for Century and Vulcan Heavy Duty units for over a year and offer superior lighting over the previous lights. This light offers "plug and play" bullet connectors so they will connect to the original light harness.

$56.99

Miller Bolt On Shackle Hanger Kit

This Shackle Hanger Kit from Miller Industries will Bolt On where you need it. This kit includes 5 hangers that bolt up to a flat surface to hang your shackles on.

$261.99

Miller Medium Offset Axle Fork Set - 6" Wide Opening

These 7.25" Medium Round Axle Forks from Miller Industries are used to pick up the axle or frame of a truck. They have a 7.25" wide opening, 2" diameter shaft, and 6.5" between the fork holder and the bottom of the cutout.

$582.99

Miller 5" x 5" Crossbar Riser Bracket Set

These Riser Brackets from Miller Industries are used when extra height is needed while towing. The riser brackets are manufactured in a welded design and incorporate a 1/2" grab hook welded to one side. With these brackets you will gain an extra 8.5" of height. Brackets will fit on a 5" x 5" heavy duty crossbar. These Riser Brackets are standard on 9055, Option for FIIIT, SDU, 5130, 5230 and 7035. Storage brackets for these riser brackets are not included.

$1,346.99

Miller LED License Light w/ Black Bracket

This is a Miller light, LED license, it has a black bracket.

$37.19

Miller Dual Snatch Block Storage Kit 2017+

Miller Industries dual snatch block storage kit fits 2017 and newer, and is a great way to store your snatch blocks. This snatch block mount holds 2 Snatch Blocks. Aluminum Construction with simple bolt-on installation. Snatch Blocks and Dri-Dek not included.

$312.99

Miller White Gel Coat Repair Kit

This is Miller white gel coat repair kit, composite bodies.

$73.99

Miller Bearing Pad Kit Steel LCG

Note: Special Handling Fees Apply

This is a Bearing Pad Kit by Miller Industries. It includes all the parts necessary to replace the wear pads on a 10 and 12 Series Steel LCG Car Carrier. See Features for a list of parts that are included. This kit is for the Gen1 series beds

(2) 12-0308927-16 5/16"x16" LCG Subframe Bearing Pads
(2) 12-0308927-66 5/16"x66" LCG Subframe Bearing Pads
(2) 12-0308927-96 5/16"x96" LCG Subframe Bearing Pads
(38) 12-0403114 1/4-20x1"x82 Deg Torx Scres
(2) 12-0306009 5/16"x1 1/4"x60" Bearing Pads

$876.99

Miller Riser Bracket

This Riser Bracket is standard on all rotators and optional of all other models. This riser bracket fits on a 4" crossbar. Sold as pair.

$1,148.99

Miller Industries 15" Slimline LED Lightbar

This light has a red lens and red led's

$73.99

Miller New Style Solenoid, Smc

This is a replacement New Style SMC Solenoid.

$161.99

Miller Wire Harness Tail Light

Can't find where the broken wire is to your taillights? Replace the wiring with this harness from Miller Industries. This part can be used to replace Part Nos.: 12-0301803 and 12-0301804.

$410.99

Miller Holmes 20" Mud Flap

Holmes logo rubber Mudflaps 20"L x 24"W. For use with most tow trucks.

$30.39

Miller Shackle Kit 12 Pieces

Miller Industries Alloy Screw-Pin Shackle Kit replaces 124002706; components will only be sold in kit form.

$2,005.99

Miller Industries Heavy-Duty Chain Tie-Down Kit

This heavy-duty chain tie-down kit from Miller Industries works with Miller's newly redesigned dual-hole fork receiver kit for heavy-duty tow operations. The kit includes one (1) T-handle ratchet binder with grab hooks and two (2) Grade 70 chain sections with a pear link at each end.

$520.99

Miller, Plate, Pin Retainer

This is a replacement pin retainer from Miller Industries.

$204.99

Miller Fold Down Bus Lift Storage System

This Miller Industries Tire Lift Storage Bracket folds down for easy access to either Part Number

$1,009.99

Buyers Keyhole Plate Banjo Eye 5/16"

This Keyhole Plate from Miller Industries has a Banjo Eye that will accept 3/8" chain. This keyhole plate is perfect if you need to add a tie-down or replace an existing tie-down. This keyhole plate can be bolted or welded into place. This plate is 3-1/2" x 3-1/2" x 5/16" thick steel that will accept 3/8" chain.

$8.39