Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
Every year more fleet managers, tradesmen, and fire chiefs outfit their trucks
with Dri-Dek. Why? Because it works. Dri-Dek cushions equipment and when it
gets wet, the raised flow-through surface lets air flow for fast drying. It
stands up to oils, grease, alkalies and solvents. It supports the weight in any
climate without cracking or buckling. Installs in minutes, lasts for years.
Sold by square foot. Also available in 3'x4' Sheets
and 3'x12' Rolls. Complete your area with the Dri-Dek corner and edge pieces to
smooth and round out your full body mat.
This zinc-plated slide-in L-Arm fits the wheel lifts on various
models of Century, Holmes and Challenger wreckers and Century, Champion,
Challenger and Vulcan car carriers.
"LED" represent the cutting edge of lighting technology, LED lights operate on
a totally different concept than traditional incandescent or bulb style lights.
Instead of using a brittle metal filament that is susceptible to road shock and
vibration. LEDs are solid-state devices utilizing an electronic chip that is
encapsulated in an epoxy substrate. This design provides increased durability
and a protective seal from road elements like dirt moisture and other corrosive
agents.
This is the Lower Cylinder Pin on the Lift Cylinder on Century Formula I Duplex
Tilt 411 & 412 wreckers. This pin also fit the Century Formula 6000 - 600
Series wrecker. To view part schematics click on the Brochures tab.
This 1" Snap Ring from Miller Industries is used on several Miller Car Carriers
and Wreckers. These include Century, Champion and Vulcan Car Carriers, as well
as, Century, Challenger, Eagle, Holmes and Vulcan Wreckers. The snap ring is
used on a wide variety of assemblies within these trucks but it is commonly
used with the Fold Cylinder Pin
This straight grease fitting is used to dispense grease into a mating part using a grease gun. It is made from steel with a zinc finish and comes with a ball check. This part has replaced part number
This is the boom end cable guide for many light duty wreckers by Miller
Industries. This cable guide replaces part number 12-0800735. See Brochures for
a reference chart and Features for related parts and wrecker models this cable
guide will fit.
This Lynch Pin from Miller Industries is used on the Mounting and Tilt Frame
Assembly of several Miller Car Carriers. These include Century, Challenger,
Champion, Holmes, and Vulcan. See the features below for a full list of
carriers and see the brochure tab for breakdowns.
Tork Advanced ShopMax Wiper 450 Center-feed shop towels are highly absorbent, offering excellent wipe-dry capabilities. Their strong construction offers durability and the self-dispensing pop-up box offers controlled dispensing. They contain 85% paper content (60% recycled, 40% postindustrial) and 15% synthetic emulsion. Sold in a box of 200.
This Pin and Link Assembly from Miller Industries is used on the Control
Components Assembly of Chevron Car Carriers. These include 14, 16, 20 and 30
Series Car Carriers. Please see the features below for a list of trucks and see
the brochure tab for breakdowns.
This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many
different Miller Wrecker assemblies. These assemblies include the boom, wheel
lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes
Wreckers. Please see the brochure for a full list of breakdowns.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is a handle bracket for Gresen V20 Valve. This piece bolts onto the valve
assembly itself and is use to hold the control rod linkage to the valve.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This Composite Bell Crank from Miller Industries is used on the 6 and 9 Spool
Control Station of Century Generation II LCG 16 Series Steel & Aluminum Car
Carriers. These carriers are made in 2014 or later. Please see the brochure tab
for a list of breakdowns.
This Pin and Link Assembly from Miller Industries is used on the Control
Components Assembly of Chevron Car Carriers. These include 14, 16, 20 and 30
Series Car Carriers. Please see the features below for a list of trucks and see
the brochure tab for breakdowns.
This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many
different Miller Wrecker assemblies. These assemblies include the boom, wheel
lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes
Wreckers. Please see the brochure for a full list of breakdowns.
This Bronze Bushing from Miller Industries is used on the Inner Boom of the
Wheel Lift Assembly of Champion Car Carriers made before 2001. This busing has
a 3" inner diameter. See the features below for a full list of carriers.
This part can be used to replace Part Numbers: 12-0301914 and 12-0301383.
This is a handle bracket for Gresen V20 Valve. This piece bolts onto the valve
assembly itself and is use to hold the control rod linkage to the valve.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This Rubber Grommet from Miller Industries is used on the Body Assembly and Light Accessory Assemblies of Miller Wreckers. These include Century, Challenger, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns. This part can be used to replace Part Number FF-116.
This Composite Bell Crank from Miller Industries is used on the 6 and 9 Spool
Control Station of Century Generation II LCG 16 Series Steel & Aluminum Car
Carriers. These carriers are made in 2014 or later. Please see the brochure tab
for a list of breakdowns.