Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
National has built a reputation as one of the most respected names in the
industry. We have offered premium sealing solutions for more than 75 years. Our
design team keeps pace with the industry and provides advanced solutions for
today's vehicles. * Temperature range: -40?F to 225?F / -40?C to 107?C *
Abrasion-resistant nitrile with spring-loaded main lip for positive sealing
with reduced shaft interference * Red 37 Series oil bath seals deliver
dependable point contact seal * Unitized construction provides greater
structural integrity, easier installation and main lip protection * Unique
rubber I.D. and O.D. includes patented SURE-LOCK? ribs that prevent shaft leaks
and bore contamination
3M Acrylic Foam Tape 4229P is a 0.76mm thick, medium-density, dark grey acrylic foam double sided adhesive tape with high performance acrylic adhesives. Double Sided Acrylic foam adhesive tape is grey with red polyethylene release liner. General purpose double sided adhesive tape with superior adhesive bonding strength for a wide variety of surfaces. Can be used to stick neodymium magnets to non-ferrous material surfaces like plastic, copper, stainless steel, wood, glass, tiles, concrete as these materials does not work directly with magnets. The acrylic foam of 0.76mm thick allows the adhesive to mould to slightly rough surfaces like concrete.
The pros know that you don't mess around when it comes to brakes. FVP Brake Cleaner meets or exceeds OE quality with a price so competitive it will stop you in your tracks. FVP Non-Chlorinated Brake Part Cleaner removes oil, grease, brake fluid and containments quickly, with no residue.
Temflex vinyl insulating electrical tape. It is flame retardant, lead free,
cold and sunlight resistant, suitable for use at not more than 600V and not
more than 80?C (176?F).
Fully annealed electrolytic copper construction provides excellent
conductivity. Wire gauge identification marked on lug barrels. Heat-shrink
tubing should be used over all battery terminal connections. Unique flared
barrel design eliminates wire strand hang-ups.
Howes Lubricator heavy-duty, multi-purpose Lubricator and Penetrating Oil is guaranteed to loosen rusted nuts and bolts. The lubricant can be sprayed on wires, leads and distributor caps and is safe to use on almost any surface.
Holmes Heavy-Duty D-Ring, Cast Iron. Typically used on Holmes 850's and 750's and some
of the larger Century hydraulic wreckers. Requires Mounting Pin (Part
#MM-8B) - Not Included.
Fastenal 11.1" 50 lbs. tensile UV black nylon 6.6 Power Phase cable tie.
Cable ties secure wire bundles, harnesses and components quickly without
slipping. Sold Each (Individually)
This is a Zip's Custom Towlight Hanger Bracket. You are able to store your
towlight when it is not in use. With this bracket you are able to customize
your toolbox by efficiently utilizing the space in your toolbox. This towlight
hanger bracket is designed to be used on the heavy duty wreckers.
Tork Advanced ShopMax Wiper 450 Center-feed shop towels are highly absorbent, offering excellent wipe-dry capabilities. Their strong construction offers durability and the self-dispensing pop-up box offers controlled dispensing. They contain 85% paper content (60% recycled, 40% postindustrial) and 15% synthetic emulsion. Sold in a box of 200.
Premium quality primary wire cable manufactured to meet or exceed ATA
specifications. Color coded PVC cover resists weather and protects the
individual color coded, annealed copper conductor strands. Commonly used to
install or repair marker/ID light circuits.
This seal kit is designed to withstand the temperatures and pressures of
hydraulic cylinders and can help operators get the maximum productivity out of
their machine. Resealing cylinders is one way to help lower operating costs and
improve the performance of your machines hydraulic system. This cylinder fits
the wheel-lift lift cylinder used on both car carriers and light duty wreckers.
See Features below to view specific models of each. To view part schematics
click the Brochures tab. Please remember that seal kits may fit different
cylinders of the same diameter. See the chart below for more information.
This is the clevis pin for the Swing L-Arm cylinder on the Century Express 300
Series, Holmes 440SL and the Vulcan 810 Power Tilt light duty wreckers by
Miller Industries. This clevis pin measures 5/8" x 1.5". This pin is used to
connect the swing L-arm cylinder to the swing L-arm. To see which specific
models this pin fits please see Features below. To view part schematics
click on the Brochure tab.
This is a Seal Kit for the Boom Lift Cylinder on Century and Holmes Light Duty
Wreckers by Miller Industries. This seal kit will fit the lift cylinder on
Century Formula I Duplex Tilt 411 & 412, and Holmes HP 552 / DFT 650. To view
part schematics click on the Brochures tab.
This is a replacement auto grip claw cylinder for second generation auto grip
autoloaders, 2003 and up. Right hand claw cylinder. This is the cylinder that
moves your right wheel retainer on your wheel lift.
This is a Pin that is used in different locations on the Wheel Lift of Century
Formula I Duplex Tilt 411 & 412, and Holmes 440 Series / DFT 400 light Duty
wreckers by Miller Industries. This pin is used to hold the tilt cylinders on
to the wheel lift frame weldment. This pin also is used to attach the upper arm
weldments to the wheel lift frame weldment also. To view part schematics click
on the Brochure tab.
This is a 1" Snap Ring by Miller Industries. This snap ring is used on the
wheel lift extend cylinder pin. This snap ring secures the pin in place. To
view the part schematic click on the Brochure tab.
This is the Swing L-Arm Cylinder, also known as the Claw Cylinder, for autoload
wreckers by Miller Industries. This cylinder will fit Century Express 300
Series, Midnight Express Series, Challenger 4300 Express Series, Holmes 440SL,
Vulcan Modular 807, 810 Intruder and 810 Power Tilt Wreckers. To view part
schematics click the Brochures tab.
This is the rear extend cylinder pin for many light duty wreckers by Miller
Industries. This pin will work with most Century, Challenger, Champion, Holmes
and Vulcan light duty wreckers. This pin measure 6" long with a diamter of
7/8". To view specific wrecker models this pin fits see Features below.
This is the L-Arm side, Swing L-Arm Cylinder Pin. This pin fits cylinder part
number 12-0303844. This pin fits Century, Challenger and Vulcan wrecker models.
To view specific models see Features below. To view part schematics click on
the Brochures tab.
This is the front extend cylinder pin for the wheel lift extend cylinder on
Miller Industries Light Duty Wreckers. It replaced part number 12-0703345. To
view what models this pin fits on please see Features below. To view part
schematics click on the Brochures tab.
This 12-004086 Seal Kit fits 10 Series Century, Holmes, Champion Wheel-lift
In/Out Cylinders using a 0302178 Cylinder 2.5" x 60" to 12/2002. This seal kit
will also fit wheel lift extend cylinder, 12-0303020, on Century, Challenger,
Champion, and Holmes Light Duty Wrecker Models. Please remember that seal kits
may fit different cylinders of the same diameter. See the chart below for more
information.
This is a replacement seal kit for the swing L-arm cylinder for autoload
wreckers by Miller Industries. This seal kit if for cylinder part number:
12-0303844.
This is the Wheel Lift Extend Cylinder on Light Duty Wreckers by Miller
Industries. This extend cylinder will fit on the following models. The Century
300 Express Series, The Century 300 Modular Express Series, The Challenger 4300
Express Series, The Holmes 440SL Series, The Vulcan Modular 807, The Vulcan 810
Intruder, The Vulcan 812 Intruder, and The Vulcan 810 Power Tilt. To view part
schematics click the Brochure Tab.
This is the Seal Kit for the Boom Extend Cylinder on Miller Light Duty
Wreckers. This seal kit is for cylinder part number 12-0301755. To view what
models this will fit see Features below. To view part schematics click the
Brochures tab.
This seal kit is designed to withstand the temperatures and pressures of
hydraulic cylinders and can help operators get the maximum productivity out of
their machine. Resealing cylinders is one way to help lower operating costs and
improve the performance of your machines hydraulic system. This cylinder fits
the wheel-lift lift cylinder used on both car carriers and light duty wreckers.
See Features below to view specific models of each. To view part schematics
click the Brochures tab. Please remember that seal kits may fit different
cylinders of the same diameter. See the chart below for more information.
This is the clevis pin for the Swing L-Arm cylinder on the Century Express 300
Series, Holmes 440SL and the Vulcan 810 Power Tilt light duty wreckers by
Miller Industries. This clevis pin measures 5/8" x 1.5". This pin is used to
connect the swing L-arm cylinder to the swing L-arm. To see which specific
models this pin fits please see Features below. To view part schematics
click on the Brochure tab.
This is a Seal Kit for the Boom Lift Cylinder on Century and Holmes Light Duty
Wreckers by Miller Industries. This seal kit will fit the lift cylinder on
Century Formula I Duplex Tilt 411 & 412, and Holmes HP 552 / DFT 650. To view
part schematics click on the Brochures tab.
This is a replacement auto grip claw cylinder for second generation auto grip
autoloaders, 2003 and up. Right hand claw cylinder. This is the cylinder that
moves your right wheel retainer on your wheel lift.
This is a Pin that is used in different locations on the Wheel Lift of Century
Formula I Duplex Tilt 411 & 412, and Holmes 440 Series / DFT 400 light Duty
wreckers by Miller Industries. This pin is used to hold the tilt cylinders on
to the wheel lift frame weldment. This pin also is used to attach the upper arm
weldments to the wheel lift frame weldment also. To view part schematics click
on the Brochure tab.
This is a 1" Snap Ring by Miller Industries. This snap ring is used on the
wheel lift extend cylinder pin. This snap ring secures the pin in place. To
view the part schematic click on the Brochure tab.
This is the Swing L-Arm Cylinder, also known as the Claw Cylinder, for autoload
wreckers by Miller Industries. This cylinder will fit Century Express 300
Series, Midnight Express Series, Challenger 4300 Express Series, Holmes 440SL,
Vulcan Modular 807, 810 Intruder and 810 Power Tilt Wreckers. To view part
schematics click the Brochures tab.
This is the rear extend cylinder pin for many light duty wreckers by Miller
Industries. This pin will work with most Century, Challenger, Champion, Holmes
and Vulcan light duty wreckers. This pin measure 6" long with a diamter of
7/8". To view specific wrecker models this pin fits see Features below.
This is the L-Arm side, Swing L-Arm Cylinder Pin. This pin fits cylinder part
number 12-0303844. This pin fits Century, Challenger and Vulcan wrecker models.
To view specific models see Features below. To view part schematics click on
the Brochures tab.
This is the front extend cylinder pin for the wheel lift extend cylinder on
Miller Industries Light Duty Wreckers. It replaced part number 12-0703345. To
view what models this pin fits on please see Features below. To view part
schematics click on the Brochures tab.
This 12-004086 Seal Kit fits 10 Series Century, Holmes, Champion Wheel-lift
In/Out Cylinders using a 0302178 Cylinder 2.5" x 60" to 12/2002. This seal kit
will also fit wheel lift extend cylinder, 12-0303020, on Century, Challenger,
Champion, and Holmes Light Duty Wrecker Models. Please remember that seal kits
may fit different cylinders of the same diameter. See the chart below for more
information.
This is a replacement seal kit for the swing L-arm cylinder for autoload
wreckers by Miller Industries. This seal kit if for cylinder part number:
12-0303844.
This is the Wheel Lift Extend Cylinder on Light Duty Wreckers by Miller
Industries. This extend cylinder will fit on the following models. The Century
300 Express Series, The Century 300 Modular Express Series, The Challenger 4300
Express Series, The Holmes 440SL Series, The Vulcan Modular 807, The Vulcan 810
Intruder, The Vulcan 812 Intruder, and The Vulcan 810 Power Tilt. To view part
schematics click the Brochure Tab.
This is the Seal Kit for the Boom Extend Cylinder on Miller Light Duty
Wreckers. This seal kit is for cylinder part number 12-0301755. To view what
models this will fit see Features below. To view part schematics click the
Brochures tab.