Search

This is an aluminum bronze bushing for a wheel lift pivot pin on a Vulcan 807 by Miller Industries.

This 1" O-Ring from Miller Industries is used on the crossbeam pivot pin of the inner crosstube weldment on the Wheel Lift and Tire Restraint Assembly of several Miller Car Carriers. These include Century, Challenger, Champion, Holmes, and Vulcan carriers. See the features below for a full list of carriers and see the brochure tab for breakdowns.

This 6.5" Thrust Washer from Miller Industries is used with a pivot pin in many different Miller Wrecker assemblies. These assemblies include the boom, wheel lift, crossbar, and underlift assemblies of Century, Challenger, and Holmes Wreckers. Please see the brochure for a full list of breakdowns.

This is a replacement Thrust Washer to be used together with a pivot pin.

This is an inner w lift tube, wide yoke, with a 2 inch pivot pin hole.

This part can be used to replace Part Number 915150001. For use with the pivot pin on Challenger Wheel Lifts.

Miller Crossbar, Century Formula wheel lift and Century & Champion carrier wheel lifts, uses WL-300K2 pivot pin kit. Fits 1996 and older Century wreckers and 2002 and older Century and Champion Car Carriers. Use 12-0803238 for newer models.

This is a replacement right hand pivot bracket for Formula I L-arm by Miller Industries. The L-arm pivot pin to use is part number 12- 0807504. This part can be used to replace Part Number 12-0904401.

This is a replacement crossbar assembly for the Vulcan V30 Gen II medium duty wrecker by Miller Industries. This assembly includes all hardware and pivot pin needed to install on your wrecker.

Note: Special Handling Fees Apply

Crossbar, Vulcan 850 and 890 series wheel lifts, uses the <a href="http://zips. com/parts-detail/vulcan-crossbar-pivot-pin-kit-890-85-vul-890k1" target="_blank"/> VUL-890K1</a/> pivot pin kit. This part can be used to replace Part Number 850020300.

• 4 X 4  square tube
• Accepts <a href="http://zips.com/parts-detail/miller-wheel-grid-assembly- left-vulcan-8900400" target="_blank"/>8900400</a/> & <a href="http://zips.com/ parts-detail/miller-wheel-grid-assembly-right-vulca-8900500" target="_blank"/> 8900500</a/> outer crosstubes
• Uses <a href="http://zips.com/parts-detail/detent-kit-century-vulcan-vul-dk1" target="_blank"/>VUL-DK1</a/> detent ball kit
• Length: 64"
• Width: 4"
• Height: 8.5"

This is a crossbar for a Challenger I-500 Invader series wheel lift. It uses the <a href="http://zips.com/parts-detail/challenger-i- 500-wheel-lift-pivot- pin-ki-i-500k2"TARGET="_BLANK"I-500K2</a pivot pin kit. This is a 2" x 3" square tube crossbar.

Note: Special Handling Fees Apply

This is a crossbar for a Century Formula I Wheel Lift Assembly. It will fit Formula I Wheel Lifts that were built in 1996 or newer. It uses a WL-300K3 pivot pin kit.

• 3" x 3" square tube
• Used on Formula I wheel lifts after March 1996
• Accepts 12-0902456 & 12-0902457 standard l-arm outer crosst ubes
• Also accepts 12-0904152 & 12-0904153 pivot l-arm outer crosstubes
• Uses WL-300DK1 detent ball kit
• Length: 53"
• Width: 4"
• H eight: 9.25"

DumperDogg Series-Power Up and Down, 1.5KW Motor (3 HP Max) For Hydraulic Pump, 6,000 lbs. Max, Dump Angle 0-45 Degrees, Includes Manual Safety Bar, Tethered Control Box w/ 9'Cord, Grease Fittings/ Holes in Pivot Pins, Includes Body Up Indicator Kit(SK10), 20' Battery Cables, Tailgate Chains, Black Powder Coat Structural Steel Frame, Double Pivoting and Removable Steel Tailgate, 3/4" Diameter Tailgate Hinge Pins.

This 3.5" x 3.5" square tube Crossbar from Miller Industries is used in the wheel lift assembly of Century 20 Series Car Carriers. It can also be used on Century Formula 6000 and Formula II Wheel Lifts with one piece pivot pins. See the brochure tab for a list of breakdowns.

This 3.5" x 3.5" square tube Crossbar from Miller Industries is used in the wheel lift assembly of Century 20 Series Car Carriers. I t can also be used on Century Formula 6000 and Formula II Wheel Lifts with one piece pivot pins. See the brochure tab for a list of breakdowns.

Note: Special Handling Fees Apply

Miller Crossbar used on Century F6500 Wheel Lifts and also on Holmes DFT 650 Wheel Lifts. This crossbar measures 3.5" x 3.5" x 56" long. It has slightly different Bolt Pattern than the early style crossbar. Pivot Pin needed for this crossbar is Part Number 12-0805858. The 5/8" Bolts required for this crossbar are part number 12-0716576. This part can be used to replace Part Number 12-0802951.

• 3.5" x 3.5" Crossbar for Century F6500 Wheel Lift & Holmes DFT 650 Wheel Lift
• Has different style bolt pattern
• Requires 5/8" Bolts
• Accepts 12-0901406 & 12-0901407 standard 3500lbs l-arm cross tubes
• Also accepts 12-0904690 & 12-0904691 medium duty 6000lbs l-arm cross tubes
• Also accepts 12-0904158 & 12-0901459 pivot style cross tubes

Note: Special Handling Fees Apply

This is a 3.5" square crossbar by Miller Industries designed for Vulcan 804, 806, 860, 870, and 880 series wheel lifts and Vulcan car carrier wheel lifts. It uses <a href="http://zips.com/parts-detail/pivot-pin-kit-vulcan-century- %2701-%2705-vul-880k1" target="_blank"/>VUL-880K1</a/> pivot pin kit. See Features for related parts and brochures for reference chart. This part can be used to replace Part Number 8700150.

• 3 1/2" x 3 1/2" square tube
• Accepts <a href="http://zips.com/parts-detail/miller-wheel-grid-3-5-vulcan- 800-seri-8800800" target="_blank"/>8800800</a/> & <a href="http://zips.com/parts- detail/miller-wheel-grid-3-5-vulcan-800-seri-8800900" target="_blank"/>8800900</a/> outer crosstubes
• Uses <a href="http://zips.com/parts-detail/detent-kit-century-vulcan-vul-dk1" _target="_blank"/>VUL-DK1</a/> detent ball kit
• Vulcan 804, 806, and 880/890 Series
  
  Related Parts:
• Pivot Pin Kit <a href="http://zips.com/parts-detail/pivot-pin-kit-vulcan-or- century-%2705-n-vul-880k2"/>VUL-880K2</a/>
• Crosstubes (CROSSTUBES3.5)

This is a replacement Pin-Pivot Weldment for the Challenger I-600 wheel lift.

A cable tensioner kit for DP winches with a 14-1/2" wide drum.

This is a 5/8" helical lock washer Zp from Miller Industries.

This is a cable tensioner kit for DP winches with a 13-3/4" wide drum.

This is a crossbar for the Century 211 by Miller Industries. See Features for related parts and brochures for reference chart.

This is a 12" cable tensioner kit for DP Model # 52864 winches and other DP winches with a 12" wide drum.

This is the outer boom of the Century Formula I 411/412 Wrecker by Miller Industries. See Brochures for a reference chart and Features for related parts.

This is the wrecker frame base for a Century Formula I 411 by Miller Industries. See Brochures for a refrence chart and Features for related parts.