Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
Order your toolbox shelving and accessories including shelf kits, storage trays, bungee straps, cab organizers, toolbox matting and more at Zips.com today! Other accessories available are rubber straps, drawer dividers, door trim and much, much more. These products are brought to you by B/A Products, Phoenix USA, Buyer’s Product Co. and more!
Every year more fleet managers, tradesmen, and fire chiefs outfit their trucks
with Dri-Dek. Why? Because it works. Dri-Dek cushions equipment and when it
gets wet, the raised flow-through surface lets air flow for fast drying. It
stands up to oils, grease, alkalies and solvents. It supports the weight in any
climate without cracking or buckling. Installs in minutes, lasts for years.
Sold by square foot. Also available in 3'x4' Sheets
and 3'x12' Rolls. Complete your area with the Dri-Dek corner and edge pieces to
smooth and round out your full body mat.
Note: Special Handling Fees Apply for Specific Items
Zip's Custom Broom or Shovel Holders are constructed of Steel and can be painted black or galvanized. These brackets are designed to be installed along side the control compartments of a Miller Industries LCG 12 & 16 Series or 10 Series Car Carriers. They simply bolt to the bottom side of the car carrier sub-frame. A threaded T-handle screws down to hold the broom or shovel securely in place.
The 12 & 16 Series custom holder measures 37.5" between the brackets. The 10 Series custom holder measures 33.5" between the brackets. These holders require you to drill through the subframe to install the brackets.
Custom built by Zip's
Choose between the 12 & 16 Series or 10 Series Car Carrier
Available in Galvanized or Painted finish
Single or Dual square tubing
Underside mount
Subframe drilling required
Additional Aluminum Mounting Plate not included in kit
These completely redesigned Lumber Baskets from In The Ditch are available in
three different lengths: 48", 60, and 70". All of these baskets are 11"
tall and 8" deep. Mounting is a snap; just bolt the basket to the back of your
tool box with six 5/16" bolts using the pre-drilled holes. In minutes you will
have a great place to store extra lumber, tire chains or anything else that you
can think of. These Lumber Baskets are made from aluminum and they have drain
holes in the bottom that will help them last for decades.
Zip's Custom Premium Toolbox Shelf Kits are an easy way to optimize the dead
space in your toolbox on your Tow Truck, Wrecker, or Car Carrier. One of the
many benefits of the premium shelf kits are you get dividers for your shelf to
help keep all of your tools organized. These premium shelf kits get bolted to
the inside of the toolbox. All necessary mounting hardware is included with
these premium shelf kits. They are made from high quality .080" thick aluminum.
These premium shelf kits not only maximize your toolbox storage space, but also
offer a custom look to the inside of your toolbox while on a recovery scene.
Use alone or stack together Front, side and back grips for easy handling Reinforced sides prevent spreading High-density, FD-approved polypropylene material holds up under heavy-duty conditions in work truck shops, towing operations and service garages. Won't rust or corrode and is unaffected by weak acids and alkalis. Built-in rear hanger allows bin to hang from louvered panels or racks.
Zip's Custom Premium Toolbox Half Shelf Kits are an easy way to optimize the
dead space in your toolbox on your Tow Truck, Wrecker, or Car Carrier. One of
the many benefits of the premium half shelf kits are you get dividers for your
shelf to help keep all of your tools organized. These premium half shelf kits
get bolted to the inside of the toolbox. All necessary mounting hardware is
included with these premium half shelf kits. They are made from high quality
.080" thick aluminum. These premium half shelf kits not only maximize your
toolbox storage space, but also offer a custom look to the inside of your
toolbox while on a recovery scene.
These Shelf Kits from In the Ditch are available in three different sizes: 48"
60" and 70". Full length shelves will essentially double the useable space inside of your toolbox. Made from aluminum, these shelves are 14" deep.
The shelves actually come as two half shelves with a vertical support, giving you the option to use them as a half shelf or full shelf. All
necessary mounting hardware is included and there is no drilled required
because of they come pre drilled.
These In The Ditch Toolbox Dividers are the perfect way to organize your
underbody box. They are made in several different lengths and come with
pre-drilled holes so installation is a snap! Take the time to divide your box
so things stay where they belong and not in one frustrating pile. Toolbox
Dividers come in five different lengths so we will have one for your box. Get
organized today!
This Floor Jack Tray from In The Ditch is a perfect solution for storing a
Floor Jack on the deck of a wrecker or inside a Tunnel Box. This Tray has a
13" x 26" tray for the jack and a 3" x 26" Tray for the jack handle
incorporated into one mount.
Every year more fleet managers, tradesmen, and fire chiefs outfit their trucks
with Dri-Dek. Why? Because it works. Dri-Dek cushions equipment and when it
gets wet, the raised flow-through surface lets air flow for fast drying. It
stands up to oils, grease, alkalies and solvents. It supports the weight in any
climate without cracking or buckling. Installs in minutes, lasts for years.
Sold by 3'x12' Rolls. Also available in 1'x1' Tiles and 3'x4' Sheets. Complete
your area with the Dri-Dek corner and edge pieces to smooth and round out your
full body mat.
Zip's Custom Standard Toolbox Shelf Kits are an easy way to optimize the dead
space in your toolbox on your Tow Truck, Wrecker, or Car Carrier. These
standard shelf kits get bolted to the inside of the toolbox. All necessary
mounting hardware is included with these standard shelf kits. They are made
from high quality .125" thick aluminum. These standard shelf kits not only
maximize your toolbox storage space, but also offer a custom look to the inside
of your toolbox while on a recovery scene.
Please Note: Product Discontinued - ALL SALES FINAL!
Discontinued items are not eligible for return. View Returns Policy
Shovel or Broom mount for car carriers simply bolts to the bottom side of the
subframe to store your shovel or broom. Threaded T-handle screws down to hold
the tool in place.
* Image shows two ZP-CBSH but these are sold individually
Image shows two ZP-CBSH but these are sold individually
For Dual see ZP-CBSH-10S-DUAL or ZP-CBSH-10S-DUAL-G
These handy shelves are not only designed to make any shop or garage more organized they just look good to. These shelves are available in 3 different widths and 5 different depths. These shelves can be mounted with a gusset down offering a smooth sleek top surface or you can turn them over for a shelf that has a lip around the top. To make your life easier we include hardware so you can mount this holder to just about anything you want. We also include special peg board screws so you can screw the holder directly to peg boards. The special screws are slightly larger than the peg board hole and work great. They can also be removed and reused so you can move or add racks without destroying your peg board. Each mount is made from Aircraft grad aluminum and come with a
100 lbs. structural load rating. Remember though, it's up to you to make sure you mount them to a surface that can support the load you put on the shelf.
This is a Northern Factory Sales auxiliary toolbox heater with 16,000 BTU and
has a high and low speed . It's compact in size 6 3/8 x 6 3/4 x 7 1/2 and is 12
Volts. This versatile heater may be mounted either horizontally or vertically.
Typical locations include floor, wall or under dash. Route the heater hose to
the engine compartment. We recommend the heater hose follow the inside of the
frame rails for protection from road debris.
Note: Special Handling Fees Apply for Specific Items
Zip's Custom Toolbox Top Tray with Light Holes. Includes (2) 6" Oval Light
Cut-Outs. With Zip's Custom Toolbox Tray you will gain extra storage on top of
your toolbox. This tray allows for additional storage for various accessories
and tools. This 20" deep tray comes in various sizes to fit on any size under
body toolbox you may have on your Tow Truck, Wrecker, or Car Carrier. This
tray is made from high quality .125" thick aluminum. Requires hardware for
bolt-on installation. 6" Oval Lights Not Included.
Note: Due to size of product, additional handling charges may
apply.
Zip's Custom Toolbox Trays
Has Light Holes
Gains Extra Storage Space
Made from High Quality .125" Thick Aluminum
Tray Lengths: 24" - 120"
Fits Most Toolboxes on Your Tow Truck, Wrecker, or Car Carrier
Every year more fleet managers, tradesmen, and fire chiefs outfit their trucks
with Dri-Dek. Why? Because it works. Dri-Dek cushions equipment and when it
gets wet, the raised flow-through surface lets air flow for fast drying. It
stands up to oils, grease, alkalies and solvents. It supports the weight in any
climate without cracking or buckling. Installs in minutes, lasts for years.
These edges are 12"x2" and are sold individually. Also available in 1'x1'
Tiles, 3'x4' Sheets, and 3'x12' Rolls. Complete your area with the Dri-Dek
corner pieces to smooth and round out your full body mat.
Zip's Custom Standard Toolbox Half Shelf Kits are an easy way to optimize the
dead space in your toolbox on your Tow Truck, Wrecker, or Car Carrier. These
standard half shelf kits get bolted to the inside of the toolbox. All necessary
mounting hardware is included with these standard half shelf kits. They are
made from high quality .125" thick aluminum. These standard shelf kits not only
maximize your toolbox storage space, but also offer a custom look to the inside
of your toolbox while on a recovery scene.
Introducing the second generation of our toolbox Box Top Tray lineup! These bolt-together Box Top Trays ship and store in a much smaller space. This also allows us to offer replacement parts in case a portion becomes damaged. All these ITD Box Top Trays now come with dividers. Giving you the choice to use them, keep them open, or install them later.
Every year more fleet managers, tradesmen, and fire chiefs outfit their trucks
with Dri-Dek. Why? Because it works. Dri-Dek cushions equipment and when it
gets wet, the raised flow-through surface lets air flow for fast drying. It
stands up to oils, grease, alkalies and solvents. It supports the weight in any
climate without cracking or buckling. Installs in minutes, lasts for years.
Sold by 3'x4' Sheets. Also available in 1'x1' Tiles and 3'x12' Rolls. Complete
your area with the Dri-Dek corner and edge pieces to smooth and round out your
full body mat.
Zip's custom center console floor toolbox is designed specifically for
Freightliner M2's. It has the ability to store a 2.8 oz. or 5lb. fire
extinguisher, TM22G 22" wireless light bar, J & C 660 and other similar jump
packs, and a Milwaukee impact and charging station. Truck Freight Ship Direct Only
These Seamless Toolbox Mats by Miller Industries are a great addition to your
toolbox to get that great custom look. Not only do they look amazing but they
are also very functional. These mats will help keep your towing tools and
accessories from sliding around and scratching and damaging the inside of your
toolbox. These mats are 12.5' long by 4' wide and are available in 5 different colors.
They are available in: Black, Blue, Yellow, Red, and Green.
Every year more fleet managers, tradesmen, and fire chiefs outfit their trucks
with Dri-Dek. Why? Because it works. Dri-Dek cushions equipment and when it
gets wet, the raised flow-through surface lets air flow for fast drying. It
stands up to oils, grease, alkalies and solvents. It supports the weight in any
climate without cracking or buckling. Installs in minutes, lasts for years.
These corners are 2"x2" and are sold as a pack of 4. Also available in 1'x1'
Tiles, 3'x4' Sheets, and 3'x12' Rolls. Complete your area with the Dri-Dek edge
pieces to smooth and round out your full body mat.
These aluminum wall hooks from In the Ditch are a versatile and easy option to organize your truck, shop, garage, or trailer. These hooks are offered in 3", 5" and 7" lengths. The heavy duty aluminum alloy construction gives these hooks a structural rating of 100 lbs. Mounting options are nearly endless including pegboard, drywall, and any other flat surface. All of the necessary hardware is included to make installation quick and easy.
This 16" Storage Tray from In The Ditch is perfect for storing just about
anything. It comes with 6 slots and 4 moveable snap in dividers. It is great
for separating and storing screws, nuts, and fittings.
These are C Tech Manufacturing drawer system 2" Risers. They help give your box
that extra bit of height to clear door openings and give you full access to
that botom drawer.
Slide 1/4"-20 hex head bolts anywhere along the slotted track for use as
hangers. Bolts are sold separately. T-slotted track is also used to position
clamps and jigs on workbenches and table saws. Track is clear-anodized
aluminum. Mounting holes are on 3" centers and require No. 8 pan head screws.
Built for medium to heavy duty trucks, Buyers Products Heavy Duty Diamond Tread
Aluminum Step Box provides framed steps with convenient built-in storage space.
The durable design incorporates a smooth aluminum body with a diamond tread
aluminum door for great stability and looks. A die cast, locking T-latch and
single rubber D-bulb door seal help keep your tools protected from weather and
theft. Corner gussets and a continuous hinge on the door opening provide extra
strength. Available in multiple sizes to suit a variety of applications.
This is a light bar for the Stellar (formerly American Eagle) drawer systems. There are three
different options to choose from. When ordering these light please use the
drawer width to assure to purchase the right fit for your drawer system.