Vulcan

Note: Special Handling Fees Apply

This Wheel Grid Assembly from Miller Industries is a right hand assembly that fits 3.5" x 3.5" square tubes. The wheel grid has a Vu lcan patented strapless system that is used on the Crossbar and Outer Crosstube Assembly of Vulcan 804, 806, 870, and 880 wheel lift s, as well as Vulcan Car Carriers. This wheel grid accepts L-Arm 8700180. Click here for the left hand version of this wheel grid 8800800.

• Vulcan patented strapless system
• Lift rating of 4,000 lbs.
• Accepts L-Arm 8700180
• Get the right hand version of this wheel gird, 8800800
  
  Fits:
  
  
• 2010-Current Vulcan Modular 804 Wreckers
• 2010-Current Vulcan Modular 806 Wreckers
• Vulcan 804, 860, 870, and 880 wheel lifts
• Vulcan car carriers

This Wheel Grid Assembly from Miller Industries is a left hand assembly that fits 3.5" x 3.5" square tubes. The wheel grid has a Vulcan patented strapless system that is used on the Crossbar and Outer Crosstube Assembly of Vulcan 804, 806, 870, and 880 wheel lifts, as well as Vulcan Car Carriers. This wheel grid accepts left hand L-Arm

This is a flange bearing for the outer stinger weldment on the Vulcan 810 by Miller Industries. See Features for related parts and brochures for reference chart.

This is an aluminum bronze bushing for a wheel lift pivot pin on a Vulcan 807 by Miller Industries.

This is a wheel lift wear pad bar for the outer stinger on light duty Vulcan wreckers by Miller Industries. There are 2 wear pads per wheel lift and they are located on the upper, outside portion of the stinger. The Vulcan models this wear pad will fit are: Vulcan Modular 880/890, 880/890, 805, 896/897. See Brochures for reference charts.

Note: Special Handling Fees Apply for Specific Items

This Stainless Steel Door Trim Kit from Miller Industries is used with a Century 3212, CXVX, or V30. Comes with two pieces of trim and a roll of adhesive to attach with.

Available in the following sizes

Item #	Size
124004574	V30-Tall-120"
124004575	V30-Tall-138"
124002613	CXVX/3212/V30 - 3 Door - 120"
124004761	CXVX/3212/V30 - 3 Door - 138"

Note: Special Handling Fees Apply

Wheel Grid assembly, right hand, fits Vulcan 850 & 890 wheel lifts. Uses 8501000 l-arm. This part can be used to replace Part Number, 8500500.

• Fits on 4" x 4" square tube
• Vulcan patented strapless system
• 6,000lbs lift rating

Bottom wear pads for the underlift on a Vulcan V60 or V70 wrecker.

This is a 1" Snap Ring by Miller Industries. This snap ring is used on the wheel lift extend cylinder pin. This snap ring secures the pin in place. To view the part schematic click on the Brochure tab.

This is the Wrecker Boom Lift Cylinder on the Holmes 440SL, Vulcan 810 Intruder, Vulcan 812 Intruder, and the Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This cylinder has a 3.5" bore with a 10.44" stroke. This lift cylinder connects to the subframe weldment and to the outer wrecker boom weldment. This is the cylinder that raises the boom of the wrecker up and down. This lift cylinder is also referred to as the boom elevation cylinder. To see which specific models this cylinder will fit please see Features below. To view part schematics click on the Brochure tab.

Note: Special Handling Fees Apply

This is a 3.5" square crossbar by Miller Industries designed for Vulcan 804, 806, 860, 870, and 880 series wheel lifts and Vulcan car carrier wheel lifts. It uses VUL-880K1 pivot pin kit. See Features for related parts and brochures for reference chart. This part can be used to replace Part Number 8700150.

• 3 1/2" x 3 1/2" square tube
• Accepts 8800800 & 8800900 outer crosstubes
• Uses VUL-DK1 detent ball kit
• Vulcan 804, 806, and 880/890 Series
  
  Related Parts:
• Pivot Pin Kit VUL-880K2
• Crosstubes (CROSSTUBES3.5)

This is the Wheel Lift Extend Cylinder Rear Pin for the Vulcan 800 Series light duty wreckers by Miller Industries. This includes the 880 / 890 Series, Modular 880 / 890 Series and the 896 / 897 Series. This pin is used to connect the wheel lift extend cylinder to the wheel lift inner boom weldment. To see which specific wrecker models this pin fits please see Features below. To view the part schematics click on the Brochure tab.

This painted steel L-Arm bracket from Miller Industries is a replacement weldment for the wheel lift on Vulcan 896, 897 and V30 light- and medium-duty wreckers. This receiver mounts to the passenger side wheel grid and secure the L-Arm, otherwise known as a scoop, wheel retainer or tire restraint.

This is the Wrecker Boom Lift Cylinder Pin for the Holmes 440SL, Vulcan 805, and Vulcan 810 Series light duty wreckers by Miller Industries. This pin goes through the base end of the lift cylinder. This pin connects the boom lift cylinder to the subframe weldment. To view part schematics click on the Brochure tab.

This is a crossbar pivot pin for a 3.5" Vulcan Crossbar

Note: Special Handling Fees Apply

Crossbar, Vulcan 850 and 890 series wheel lifts, uses the VUL-890K1 pivot pin kit. This part can be used to replace Part Number 850020300.

• 4 X 4  square tube
• Accepts 8900400 & 8900500 outer crosstubes
• Uses VUL-DK1 detent ball kit
• Length: 64"
• Width: 4"
• Height: 8.5"

This is the Wheel Lift Tilt Cylinder Pin for the Vulcan 810 Power Tilt light duty wrecker by Miller Industries. This pin goes through the base end of the tilt cylinder. This pin attaches the tilt cylinder to the wrecker outer boom weldment. To view the part schematic click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder Lower Pin on the Vulcan 880 / 890 Series and the Vulcan 896 / 897 Series light duty wreckers by Miller Industries. This pin is also used to attach the wrecker boom lift cylinder to the subframe weldment on the Vulcan 896 / 897 Series wrecker. To see which specific wrecker models this pin will fit please see Features below. To view the part schematics click on the Brochure tab.

This Miller Industries product is a full assembly of the right side of a tail light section on a car carrier. It is designed for Vulcan Car Carriers. It includes all the necessary parts to replace the entire tail light section this product bolts into the mounting bracket which is attached to the subframe of the carrier.

This is the Wheel Lift Tilt Cylinder Lower Pin for the Vulcan 810 Intruder light duty wrecker by Miller Industries. This pin goes through the rod end of the tilt cylinder. This pin attaches the wheel lift tilt cylinder to the wheel lift outer boom weldment. To view the part schematic click on the Brochure tab.

This Miller Industries product is a full assembly of the left hand side of a tail light section on a car carrier. It is designed for Vulcan Car Carriers. It includes all the necessary parts to replace the entire tail light section. This product bolts into the mounting bracket which is attached to the subframe of the carrier.

This is the Wheel Lift Tilt Cylinder for the Vulcan 880 / 890 Series light duty wreckers by Miller Industries. This cylinder allows your wheel lift to tilt up and down. This cylinder connects to the wheel lift tilt column and the subframe of the wrecker. To view the part schematic click on the Brochure tab.

This zinc-plated mild steel L-Arm from Miller Industries fits the driver side of the wheel lift on Vulcan 896 and 897 medium-duty wreckers. Otherwise known as a tire restraint or wheel retainer, the 2" x 3" rectangular tube fits the 12-4008001 outer crosstubes and offers adjustment holes and a grated tire scoop pan for tire securement.

This is the spacer bar by Miller Industries that is located on the up/down portion of the outer stinger weldment on a Vulcan Light Duty Wreckers. This spacer bar will fit on the following models: Vulcan Modular 880/890, 880/890, 896/897. There are two of these spacer bars for each wheel lift. See features for related hardware and see brochures for reference charts. Sold as Each.

This is the Wheel Lift Tilt Cylinder Lower Pin for the Vulcan 812 Intruder and the Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This pin goes through the rod end of the tilt cylinder. This pin attaches the tilt cylinder to the wheel lift outer boom weldment. To see which specific wrecker models this pin will fit please see Features below. To view the part schematics click on the Brochure tab.

This is a wear pad holder on the up/down portion of the wheel lift by Miller Industries. It is bolted on by tow bolts and there are 2 wear pad holders per wheel lift. This wear pad holder fits the following wreckers: Vulcan 880/890, Modular 880/890 and 896/897. See Features for related hardware and Brochures for reference charts.

The all around manual for Vulcan 10 Series Aluminum & Steel Car Carriers. This manual includes installation guides, operation guides, and how to maintain your carrier. The manual also has a section on all of the parts that make up the carrier, so if you have a problem you can easily find the replacement part.

This is the Wrecker Boom Lift Cylinder Upper Pin for the Vulcan 805, Vulcan 806, Vulcan 807 Auto Grip, and Vulcan 810 Intruder light duty wreckers by Miller Industries. This pin goes through the rod end of the lift cylinder. This pin connects the lift cylinder to the outer wrecker boom weldment. To see which specific wrecker models this cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Wheel Lift Extend Cylinder Front Pin for the Vulcan 880 / 890 Series and the Modular 880 / 890 Series light duty wreckers by Miller Industries. This pin is used to connect the wheel lift extend cylinder to the wheel lift outer boom weldment. To see which specific wrecker models this pin fits please see Features below. To view the part schematics click on the Brochure tab.

This is the Wheel Lift Extend Cylinder on the Vulcan 880 / 890 Series and the Modular 880 / 890 Series light duty wreckers by Miller Industries. This cylinder connects the inner and outer wheel lift boom weldments together. This cylinder is what extends the wheel lift stinger out and in. To see which specific models this cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Lower Lift Cylinder Pin on the Wheel Lift of the Vulcan 880 / 890 Series and the Modular 880 / 890 Series light duty wreckers by Miller Industries. This is the lower pin and it goes through the rod end of the cylinder. This cylinder connects the lift cylinder to the wheel lift outer boom weldment. To see which specific wrecker models this pin will fit please see Features below. To view the part schematics click on the Brochure tab.

These kits are Stainless Steel Door Trim Kits from Miller desighed for Vulcans.

This Seal Kit from Miller Industries is used on the Bed Tilt Cylinder

This is the Upper Lift Cylinder Pin on the Wheel Lift of the Vulcan 880 / 890 Series and the Modular 880 / 890 Series light duty wreckers by Miller Industries. This is the upper pin and it goes through the base end of the cylinder. This cylinder connects the lift cylinder to the wheel lift tilt column weldment. To see which specific wrecker models this pin will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder Upper Pin on the Vulcan 805 light duty wrecker by Miller Industries. This pin goes through the base end of the tilt cylinder. This pin attaches the tilt cylinder to the wrecker outer boom weldment. To view the part schematic click on the Brochure tab.

This adjustable L-Arm from Miller Industries fits the driver side of the wheel lift on Vulcan 896 and 897 medium-duty wreckers. Otherwise known as a tire restraint or wheel retainer, this zinc-plated mild steel 2" x 3" rectangular tube fits the 12-4008001 outer crosstube. The L-Arm is angled in and downward to create additional clearance on smaller vehicles. The scoop style tire pan is also grated for improved grip.

This is the Lift Cylinder on the Wheel Lift of the Vulcan 880 / 890 Series and Modular 880 / 890 Series light duty wreckers by Miller Industries. This cylinder attaches to the wheel lift tilt column weldment and to the wheel lift outer boom weldment. This is the cylinder that raises your wheel lift on your wrecker up and down. To see which specific wrecker models this cylinder fits please see Features below. To view the part schematics click on the Brochure tab.

This is a replacement front mounting pin weldment for the extend cylinder on heavy duty Vulcan wreckers. This pin fits the V-60, V-70, V-90, and V-100 heavy duty wreckers by Miller Industries. This pin attaches the wheel lift stinger extend cylinder to the wheel lift folding boom weldment. To view part schematics please click on the Brochure tab.

This is the Wheel Lift Extend Cylinder Pin for the Wheel Lift of the Vulcan 805 light duty wrecker by Miller Industries. This pin goes through the rod end of the cylinder. This pin is used to attach the wheel lift extend cylinder to the wheel lift inner boom weldment. To view the part schematic click on the Brochure tab.

This is the boom pivot pin wedment for a Vulcan 880/890 Wrecker by Miller Industries.

This is the Wrecker Boom Lift Cylinder for the Vulcan 880 / 890 Series light duty wreckers by Miller Industries. This cylinder attaches to the outer wrecker boom weldment and the subframe of the wrecker. This cylinder raises the boom of your wrecker up and down. This cylinder can also be referred to as the boom elevation cylinder. To view the part schematic click on the Brochure tab.

Crossbar, Vulcan 896 & 897 wheel lift

This is the Wheel Lift Tilt Cylinder for the Vulcan 806 and Vulcan 807 Auto Grip light duty wreckers by Miller Industries. This is the cylinder that tilts the wheel lift of your wrecker up and down. This cylinder is attached to the wrecker outer boom weldment and the wheel lift outer boom weldment. To see which specific wrecker models this cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Wrecker Boom Lift Cylinder Pin on the Holmes 440SL, Vulcan 812 Intruder, and the Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This pin goes through the rod end of the lift cylinder. This pin connects the boom lift cylinder to the main boom of the wrecker. To see which specific models this pin will fit see Features below. To view part schematics click on the Brochure tab.

This is the Wrecker Boom Lift Cylinder for the Vulcan 880 / 890 and 896 / 897 Series light duty wreckers by Miller Industries. This cylinder attaches to the outer wrecker boom weldment and the subframe of the wrecker. This cylinder raises the boom of your wrecker up and down. This cylinder can also be referred to as the boom elevation cylinder. To see which specific models this lift cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Wrecker Boom Lift Cylinder for the Vulcan 805, Vulcan 806, and Vulcan 807 Auto Grip light duty wreckers by Miller Industries. This is the cylinder that raises the wrecker boom up and down. This cylinder attaches to the wrecker subframe weldment and to the wrecker outer boom weldment. This cylinder is also referred to as the boom elevation cylinder. To see which specific wrecker models this cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is a replacement boom lift cylinder for the Vulcan V-70 and V-90 heavy duty wreckers by Miller Industries. This lift cylinder connects to the wrecker's subframe and to the outer boom weldment. This cylinder is designed to fit the right and left side of the wrecker. To view the models this cylinder fits, see Features below. To view the part schematics, see the Brochure tab.

This is a replacement boom extension cylinder for the Vulcan V-60, V-70, V-90, and V-100 heavy duty wreckers by Miller Industries. This cylinder connects to the inner and outer boom weldments and extends the inner boom weldment away from the wrecker. To view the models this cylinder fits, see Features below. To view the part schematics, see the Brochure tab.

This is the Wrecker Boom Extend Cylinder Pin for the Vulcan 880 / 890 Series and the Vulcan 806 Series light duty wreckers by Miller Industries. This pin is used to secure the boom extend cylinder to the inner wrecker boom weldment. To view the part schematic click on the Brochure tab.

This is the Wrecker Boom Extend Cylinder Pin for the Vulcan 896 and 897 Series light duty wreckers by Miller Industries. This cylinder pin goes through the rod end of the cylinder. This pin connects the boom extend cylinder to the wrecker inner boom weldment. To view the part schematic click on the Brochure tab.

This is a 1" Heavy Duty extended retaining / snap ring that is used on the boom and underlift of wreckers.

This is the Wheel Lift Tilt Cylinder for the Vulcan 805 Series light duty wrecker by Miller Industries. This is the cylinder that tilts the wheel lift of the wrecker up and down. This cylinder attaches to the wheel lift outer boom weldment and the wrecker outer boom weldment. To view the part schematic click on the Brochure tab.

This is a top cover plate for a Vulcan 880/890 Wheel Lift by Miller Industries. It is bolted down by two bolts. See features for related hardware and see brochures for a reference chart (item #27).

This is the Wheel Lift Extend Cylinder for the Vulcan 805 light duty wrecker by Miller Industries. This cylinder attaches to the wheel lift outer and inner booms. This is the cylinder that extends the wheel lift in and out on your wrecker. To view the part schematic click on the Brochure tab.

This is the Wrecker Boom Extend Cylinder Pin for the Vulcan 880 / 890 Series light duty wrecker by Miller Industries. This pin has a 1-1/4" diameter and a length of 6-5/8". This pin is used to secure the boom extend cylinder to the outer wrecker boom weldment. To view the part schematic click on the Brochure tab.

This is the Wheel Lift Extend Cylinder Pin for the Wheel Lift of the Vulcan 805 light duty wrecker by Miller Industries. This pin goes through the base end of the cylinder. This pin is used to attach the wheel lift extend cylinder to the wheel lift outer boom weldment. To view the part schematic click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder on the Vulcan 896 and 897 Series light duty wreckers by Miller Industries. This is the cylinder that tilts the wheel lift up and down on your wrecker. This cylinder attaches to the wrecker subframe and to the wheel lift tilt column. To view the part schematic click on the Brochure tab.

This is the Wrecker Boom Extend Cylinder Pin for the Vulcan 896 and 897 Series light duty wreckers by Miller Industries. This cylinder pin goes through the base end of the cylinder. This pin connects the boom extend cylinder to the wrecker outer boom weldment. To view the part schematic click on the Brochure tab.

This is the Wheel Lift Extend Cylinder Front Pin for the Vulcan 896 and 897 Series light duty wreckers by Miller Industries. This pin goes through the base end of the extend cylinder. This pin connects the wheel lift extend cylinder to the wheel lift outer boom weldment. To view the part schematic click on the Brochure tab.

This is the Lower Lift Cylinder Pin on the Wheel Lift of the Vulcan 896 and 897 Series light duty wreckers by Miller Industries. This pin goes through the rod end of the lift cylinder. This pin connects the lift cylinder to the wheel lift outer boom weldment. To view the part schematic click on the Brochure tab.