Tools and Equipment

Sort by

Miller Bus Lift Eye Attachment

The 124002634 Lift Eye Attachment is designed for front lifts on many models of the RTS, GMC, and NOVA buses and rear picks on the MCI-9. The rear eye on an MCI ,GL, and GL3 series can be utilized for a rear pick. The eyelet that is bolted on to the jack pad point on many RTS, GMC, and NOVA buses is pinned into the lift eye attachment for a front pick.

$367.99 – $877.99

Miller Fork Spacer Set

Spacers for use with the Century forks from Miller Industries. This attachment was designed to be used when the front axle you are picking up is narrower than the throat of the fork you are using. Simply slide the adapter over one ear of the fork and you have created 1" narrower opening in your fork without having to carry extra attachments in your tow vehicle. Remember to always use safety chains.

$233.99

Miller Short Axle Fork - 5" Wide Opening

This Short 5" Fork from Miller Industries is used to pick up from the leaf spring, axle or frame. These Forks are made from one piece of cast alloy steel that increases the yield strength almost two fold while also making them 30% lighter than the old fork designs. This fork has a 5" wide opening, a 2" diameter shaft and a 3" clearance between the fork holder and the bottom of the fork cutout.

$253.99 – $445.99

Miller Medium Axle Fork - 5" Wide Opening

This cast steel alloy Fork from Miller Industries is used to pick up from the leaf spring, axle or frame. Making these forks from one piece of cast steel has increased the yield strength almost two fold while also making them 30% lighter than the old fork designs. This fork has a 5" wide opening, 2" diameter shaft and has a 6-1/4" clearance between the fork holder and the bottom of the fork cutout.

$268.99 – $472.99

Miller Dual Fork Receiver Set

Miller Industries newly redesigned and field-tested dual fork receiver set offers heavy-duty tow operators the advantage of four fork positions on their crossbars, allowing them to achieve the desired clearance and weight distribution on their underlifts during front-pick tows.

$2,499.99 – $4,013.99

Miller Tall Axle Fork - 5" Wide Opening

Cast Steel Alloy Forks from Miller Industries are used when clearance is needed on a vehicle with a low front end. These forks are made in one piece using a special cast steel process. There is a 5" wide opening at the top of the fork and the shaft has a diameter or 2". There is a 9" clearance between the fork holder and the bottom of the fork cutout. The yield strength has been increased while making them almost 30% lighter than the old fork designs.

$346.99 – $617.99

Miller U-Bolt Lifting Attachment Set

This U-Bolt Lifting Attachment is designed for faster and easier rear hookups on many tractors. The attachment is centered on one of the rear U-bolts on each side and then the underlift is raised. The U-bolt attachment lifts on the bolt saddle while the U-bolt and nut guide it into position. These attachments are designed for Rear Lift Only. 1 Pair Included in Kit.

$628.99

Miller Shackle Hanger Kit

This Shackle Hanger Kit is from Miller Industries. This kit includes 5 shackle hangers.

$261.99

Miller Offset Chain Hook Adapter Version 2 for Dual Fork Holders

Miller Industries has improved the design of its offset chain hook adapter by adding a second pin for stability and reinforcing the chain hook block for additional strength. This updated version now slides into two holes on a heavy-duty fork holder found on 5" x 5" crossbars on Century, Vulcan and Holmes underreaches.

$1,296.99

Miller Wheel Lift Anchor Spade (FI DFT-400 I-400)

This Miller Industries Wheel Lift Anchor Spade fits Century Formula I, Holmes DFT-400, and Challenger I-400. The wheel lift spade is designed to fit over the outer tube of the wheel lift and use the downward force of the wheel lift to anchor the truck while winching.

$379.99

Miller Universal Fork Holder, 3.5"x4"

Miller offset fork adapter for 3.5" x 4" crossbars. This fork adapter is commonly used on Vulcan V30 Wreckers.

$736.99

Miller Chain Hook Adapter Set

Miller Industries chain hook adapter kit. These chain hook tow bar adapters are specifically designed to fit the cast profile fork holders of Century and Vulcan Heavy Duty Wreckers. They are used when lifting a load when chains are required. For more versatility they may moved back and forth on the crossbar to fit the size of the load being picked up. Sold as a pair.

$1,029.99

Miller King Pin Tow Plate / Trailer Recovery Loop

This King Pin Tow Plate Recovery Loop from Miller Industries was designed to be attached to the fifth-wheel pin on a large trailer so that it can be towed without the presence of a tractor. Slide the plate on to the pin, attach your chains, secure them to your sling and lift. Use your safety chains anytime you are towing for maximum security and safety. This part has replaced part number 124001674.

$319.99

Miller Spreader Bar Kit Long

Miller Industries Spreader Bar Kit. Miller Industries has developed a new spreader bar to work in conjunction with their full integrated and rotator product lines. Designed for use in all types of heavy and light duty lifting applications, this unique spreader bar allows for executing straight vertical lifts without damaging or collapsing the sides of the casualty.

$4,154.99

Miller Volvo Axle Fork Set - 8" Wide Opening

Miller Industries Specially designed for lifting the Hendrickson Airtek/Steertek front axle is the hollow beam lifting fork. Special care must be taken when lifting the air suspension hollow beam front axles currently being used on many of the Volvo VNT and Freightliner Century Tractors making this fork or a front tire lift a must.

$817.99

Miller Heavy Duty Tire Lift Attachment Crossbar

To expand your lifting capabilities your Century can be equipped with the optional wheel lift grid system. This system is available to fit the 4", 5", and 6" crossbars. It is capable of towing vehicles from both the front and rear axles, in either single or dual tire applications. It offers versatility, with a wide range of adjustment for nearly all sizes of tire, as well as axle widths.

$5,141.99 – $5,828.99

Miller Bolt On Shackle Hanger Kit

This Shackle Hanger Kit from Miller Industries will Bolt On where you need it. This kit includes 5 hangers that bolt up to a flat surface to hang your shackles on.

$261.99

Miller Medium Offset Axle Fork Set - 6" Wide Opening

These 7.25" Medium Round Axle Forks from Miller Industries are used to pick up the axle or frame of a truck. They have a 7.25" wide opening, 2" diameter shaft, and 6.5" between the fork holder and the bottom of the cutout.

$582.99

Miller 5" x 5" Crossbar Riser Bracket Set

These Riser Brackets from Miller Industries are used when extra height is needed while towing. The riser brackets are manufactured in a welded design and incorporate a 1/2" grab hook welded to one side. With these brackets you will gain an extra 8.5" of height. Brackets will fit on a 5" x 5" heavy duty crossbar. These Riser Brackets are standard on 9055, Option for FIIIT, SDU, 5130, 5230 and 7035. Storage brackets for these riser brackets are not included.

$1,346.99

Miller Dual Snatch Block Storage Kit 2017+

Miller Industries dual snatch block storage kit fits 2017 and newer, and is a great way to store your snatch blocks. This snatch block mount holds 2 Snatch Blocks. Aluminum Construction with simple bolt-on installation. Snatch Blocks and Dri-Dek not included.

$312.99

NRC Adjustable Spreader Bar

This short spreader bar is easy enough for one guy to handle and set up. It comes with 3 sections that are rated for 60,000 lbs. at 7'6" at 60 degrees. At full extension, 12'4", they are rated for 35,200 lbs. at 60 degrees. Size of holes are 1 1/2"

$1,899.99

Miller Riser Bracket

This Riser Bracket is standard on all rotators and optional of all other models. This riser bracket fits on a 4" crossbar. Sold as pair.

$1,148.99

Miller Vulcan V-30 Fork Holder 3.5" X 4" Universal

These fork holders are designed to fit a 3.5" x 4" crossbar. They are a universal style fork holder and are commonly used with the Vulcan V-30 Medium Duty Wreckers.

$1,200.99

Miller Fold Down Bus Lift Storage System

This Miller Industries Tire Lift Storage Bracket folds down for easy access to either Part Number

$1,009.99

Miller Spreader Bar Mounting Brackets

These Spreader Bar Storage Brackets From Miller Industries are a great way to store you spreader bar on the top of your body side on a heavy duty wrecker. Sold as Pair.

$154.99

Miller Fork Adapter for 3" X 3" Crossbar Fork Holder

This is a replacement 3" x 3" fork adapter.

$371.99

Miller Ball Bracket Trailer Hitch Adapter (Century F6500 / DFT-650)

This Trailer Hitch Adapter from Miller Industries is used on a Century Formula 6500 and Holmes DFT-650 Wheel Lift. It allows you to tow a trailer with a ball type hitch behind your wheel lift. This adapter installs quickly and it is small enough to fit in your toolbox when it is not being used.

$382.99

Miller Forklift to Wheel Lift Attachment

The Eagle Fork-lift Attachment. Fast, damage free, car moving machine. Turns a forklift into a fast efficient yard truck! Move cars quickly from parking spots, within storage yards or salvage lots. All you need is a forklift. Just slide the forks into the receivers and you are ready to go. No hydraulics just a simple rotating mechanism which wraps around the car tires!

$6,289.99

Miller King Pin Tow Plate Storage Bracket

This is a King Pin Tow Plate Storage Bracket from Miller Industries.

$251.99

Miller Snatch Block Storage Rack

Miller Industries snatch block storage racks for heavy duty wrecker lines. The storage kits allow the hook to be at the top for easier placement of the block in the storage compartments. These storage racks are offered in 3 size formats including a dual, quad and pod box for rotators. The pod box systems store up to 8 snatch blocks.

$338.99 – $1,071.99

Miller Spreader Bar Storage Kit End Caps

This Spreader Bar Storage Kit allows you to securely store your end caps for your spreader bar. It will help you prevent misplacing your end caps, and helps protects them from damage while heading out to a recovery scene.

$466.99

Miller 4" x 4" Crossbar Riser Bracket 8" Lift

This riser bracket is for a 4" by 4" crossbar used on a Century 3024 and 4024. They accept most 2" diameter forks and are used when extra height is needed for towing.

$605.99

Miller Offset Fork Holder Set for 4" x 4" Crossbar

These Low Profile Fork Holders are designed to fit a 4" x 4" crossbar. They are made from the same special cast alloy material as the other Miller products . This fork holder set includes the right and left hand sides.

$2,298.99

Miller Fifth Wheel King Pin Adapter 16 Ton Wreckers

This is a Miller Industries Pintle Hook and Fifth Wheel Adapter Kit. It is designed specifically for Miller 16 ton wreckers including the Vulcan V-30, Century 3212, Vulcan V-24 and Holmes 600R. It fits a 3" x 4" crossbar.

$1,949.99

Miller Rotator Spade Attachment

Heavy-duty tow operators seeking to increase traction on sidepull recoveries can purchase this newly-designed spade attachment for the H-beam outriggers on their Century rotators. Improving on the old style, engineers at Miller Industries have created more downward pressure and reduced weight by eliminating angle bracing and adopting a more vertical application for this user-friendly accessory.

$704.99

Miller Swing Arm Style Dolly Mount

Swing Arm Style Dolly Mount Bracket-Mounts on the rear tailgate section next to the wheel lift boom allowing for better rear visibility and freeing up the upper deck area for mounting additional equipment such as fuel cans or air tanks. The swing arm is released by a camlock that allows the dollies to swing past the side or tail section for better access and the lower mounting height making them easier to lift on and off. Sold as a pair, so you get 2 dolly mounts. One for each side of your wrecker.

$1,471.99

Miller Red and Yellow Safety Tape

Red and yellow safety tape from Miller.

$145.99

Miller Trailer Hitch Adapter Ball Bracket Formula I

This Trailer Hitch Adapter from Miller Industries is used on a Century Formula I Wheel Lift that was made after March of 1996. It allows you to tow a trailer with a ball type hitch behind your wheel lift. The Hitch installs quickly and it is small enough to fit in your tool box when it is not being used. Also fits a Holmes DFT-400 and Challenger I-400 Wheel Lift.

$382.99

Miller Reese Receiver Adapter (Gen 1 Car Carrier Wheel Lifts)

This Reese Receiver Wheel Lift Adapter from Miller Industries is used on Car Carriers. This removable adapter is specifically designed to be mounted on Miller's Century, Champion, Chevron and Vulcan conventional Car Carrier Wheel Lifts, which have the built-in ball hitch receiver. This 2" universal receiver accepts and pintle or ball hitch with a 2" tube. It is accepted on 10 Series, 12 Series LCG and 16 Series LCG GEN1 built before Sept. 2016 standard wheel lifts. All of the mounting hardware is included on this adapter. For a complete Pintle Hook Receiver Kit see part # ZP-CC-PHK. This part can be used to replace Part Number 12-0809073.

$540.99

Miller Chain Hook End Caps (4024), 4" Crossbar

Miller Industries Hook End Cap. Fits a Century 4024 Wrecker with a 4" crossbar. Sold as Pairs.

$726.99

Miller Offset Fork Holder

This is an offset fork holder from Miller Industries. These forks come on 25 ton and larger wreckers. This offset fork holder fits a 5" crossbar. Sold as pair.

$1,649.99

Miller Rotator Spade Attachment Storage Bracket

This bolt-on under-mount bracket is specifically designed to store Miller's outrigger spade attachment on Century rotators. The steel bracket can mount near the outriggers so it's readily available when heavy-duty operators are seeking additional traction on side load recovers. Installing it under the body prevents damage from other equipment and tools and also preserves valuable storage space inside toolboxes. The bracket is powder-coated black to guard against road spray and premature corrosion.

$368.99

Miller End Cap Chain Adapter (16 Ton Wreckers)

Miller Industries End Cap Chain Hook Adapter for Vulcan V30, Century 3212, and Holmes 600R 16 Ton Wreckers with low profile 3" x 4" crossbar.

$384.99

Miller Spreader Bar Tube Short

Miller Industries SHORT Spreader Bar. Includes the short tube only. Allows for 58", 63" and 68" Lengths. Spreader Bar Ends sold separately.

$947.99

Miller Approach Plate Roller Guide

This new approach plate roller guide attachment is for 10, 12, and 16 Series Steel car carriers. This new attachment enables 180 degrees of light-duty recovery capability at the back of the carrier. The roller guide attaches to the approach plate and fits steel car carrier beds only that are 2018 and newer. This roller guide attachment is designed to be used with 3/8" and 7/16" wire rope and it is rated for 3,500 lbs. of line pull. The roller guide attachment is engineered to the highest standards of durability, and is constructed of fabricated steel with zinc plating for corrosion resistance.

$924.99

Miller Curved Axle Fork Set

This replacement Curved Axle Fork Set from Miller Industries features a short front lead fork to easily fit under an axle. The rounded inner design fits nicely around the axle.

$931.99

Miller Medium Duty Truck Hitch

This Medium Duty Truck Hitch from Miller Industries has superior strength and durability. This might be the best tow bar design ever because it incorporates the use of extra-large spacer bars, a smooth faced crossbar and cam locks on the spacer bars for easier use. The crossbar comes with 1/2" grab hooks at the end for extra heavy duty lifting, and 3/4" shackles for attaching your winch cable to. Mounting brackets sold separately.

$4,784.99

Miller 16 Ton Wrecker Riser Bracket Set

These Miller riser brackets can be used on the Vulcan V30, Century 3212, and a Holmes 600R 16 Ton Wreckers. These risers are 7" that are mainly used when extra height clearance is needed for towing.

$2,135.99

Miller 25,000 lb. (50 - 75 Ton) Tire Lift

Miller Industries 25,000 lb. Tire Lift For The Century 7035, 9055 and Rotator Series, Vulcan V-70, V-100 and Challenger's Complete Line of Towing and Recovery units (5" x 5" Crossbar). This New Tire Lift (124002808) Will Include The Upgraded Crossbar (124002838) When Ordered On With A New Wrecker Unit.

$6,716.99

Century Trailer Ball Adapter Formula 1 Wheel Lift

This trailer hitch adapter is for Century Formula 1 Wheel Lifts. It was manufactured before March of 1996. This adapter will allow you to tow a trailer with a ball type hitch behind your wheel lift. It installs quickly and is small enough to fit into your tool box with it is not in use. This hitch adapter comes with a 2" trailer ball, mounting bolts and a primed adapter. This trailer ball adapter also fits Holmes DFT-400 and Challenger I-400 wheel lifts that were manufactured before March of 1996 and Century/Champion car carriers that were manufactured before January 2000.

$280.99

Miller 6,000 LB Tire Lift Kit (4" x 4" Crossbars)

Miller Industries 6,000 Lb. Tire Lift System To Fit a 4" x 4" Crossbar. Fits 1624, CH20, 4024 Wrecker Models.

$4,110.99

Miller Tunnel Box Fork Holder Kit

Store your forks with this Fork Holder Storage Kit. This storage kit can be used on a 36" OR 48" Tunnel Box.

$1,004.99 – $1,174.99

Miller 12.5' Telescoping Ladder

This Telescoping Ladder from Miller Industries is easy to store, transport and maneuver. The telescoping mechanism adjusts the ladders height up to 12.5' and the intelligent design allows for safe, effortless single person operation. This part can be used to replace Part Number 124004413.

$750.99

Miller 16 Ton Fifth Wheel Assembly

This fifth wheel assembly from Miller Industries is used with 16 Ton Wreckers Pintle Hitch Adapters. This kit includes quick pin, handle grip, linch pin, 5th wheel bracket, lock pin and pivot pit adapter.

$862.99

Miller King Pin Attachment

This king pin attachment requires

$996.99

Miller Heavy Duty "Euro" Style Bus Lift 5" x 5" Crossbar

Miller Industries has begun manufacturing a Tire Lift System for the North American market that was originally pioneered by Boniface Engineering of England several decades ago. This attachment will only be available with units offering the 5 x 5 crossbar. It is capable of towing vehicles from both the front and rear axles, in either single or dual tire applications. It offers versatility, with a wide range of adjustment for nearly all sizes of tire, as well as axle widths.

$5,623.99

Miller Offset Fork Holder Extensions

The extensions were designed to provide extra width out of the lift fork adapters when needed. Place the extensions into the fork adapters, install the retaining bolts, slide to the desired width and it's ready to tow. Extensions sold by the pair and will only fit the low profile cast fork holders.

$1,391.99

Power Pal Pouch

$60.99

Miller Camlock Assembly Side Winder

This is a replacement side winder camlock assembly.

$161.99

Miller Side Pull Stabilizer

This Miller Industries Side Pull Stabilizer is designed to pin on and off the multiposition rear spades on the Century and Challenger integrated and fixed boom heavy duty towing and recovery units. The side pull stabilizer provides additional stability on side and corner pull applications. (One per kit)

$726.99

1 - 60 of 96 items