Towing Accessories

The Traveling Speed Chock from In The Ditch helps prevent vehicles from rolling off the deck of a car carrier during loading and unloading. Chock travels up the deck with the vehicle and will help prevent the vehicle from rolling off the deck should you have a catastrophic failure of the winch of wire rope. People who have used it are calling in a Life Saver! The chock can be set up to work from the passenger or driver side. It will easily adjust to fit most passenger vehicles. The rubber chock is sipped for better holding ability. Shop our large selection of

These Fork Extenders from AW Direct adds 14" to your underreach to provide clearance around axle housings, steering boxes and off-road axles. This functional, heavy-duty attachment is designed for the left or right side of your lift and fits 4" square crossbars and 2" round axle forks.

The AW Direct Elite Series U-Bolt Attachment makes towing road tractors from the rear a cinch. The beveled design of the opening helps guide the u-bolt and nut from the rear spring assembly directly into the attachment. Simply pick the rear axles off the ground, chain up the suspension, securely tie-down the tractor to the wheel-lift and away you go!

This Large ITI Machinery Skate is designed specifically for moving equipment and other heavy machinery. These ITI Skates will drastically reduce the moving resistance allowing for easier placement of heavier equipment while protecting the floor. The low-profile design features a beveled cutout on the skate surface to cradle machinery legs, when needed. Flip this skate upside down and use it as a loading ramp to provide a tapered approach.

These tall forks give you plenty of clearance between your crossbar and the bottom of the fork trough so you can access engines with deep oil pans.

The Soft Ties from Condor help to protect your paint and chrome when tying down your bike. Use these soft ties with a heavy duty ratchet tie-down to ensure a secure bike during transport. These straps are blue and are sold as pairs.

Note: Special Handling Fees Apply

1-1/4" Hand Rail Kit from Miller Industries. This Kit includes 2 20' rail pieces, stanchions, and fasteners needed.

• 1-1/4" Hand Rail Kit
• Includes all rails, stanchions, and fasteners needed

The CONDOR Soft Covers are specifically designed for use with the CONDOR Ratchet Tie-Down Straps. The Soft Covers feature reinforced nylon stitching and fur covering to provide the most protection for precious chrome and paint from scratches, dents and damage while transporting your motorcycle, ATV, or whatever you need to tie down and haul. It's a little extra piece of mind.

This set of two XTenders can only be used with 7-inch lift HD Tow Ramps to further lower the angle of approach. Simply place the XTenders on top of the Tow Ramps and drive on up! The XTenders can also be inverted for use as a "œhumper" ramp to get a bit of additional lift when needed. They are 10 inches wide and 35 inches long, weighing 6 pounds each.

These fork holders are designed to fit a 3.5" x 4" crossbar. They are a universal style fork holder and are commonly used with the Vulcan V-30 Medium Duty Wreckers.

Plunger Pin Kit for Holmes TS-100 tow sling. 5/8" diameter pins.

This is a King Pin Tow Plate Storage Bracket from Miller Industries.

This is a 2 function handheld transmitter from Mobile Control Systems.

This Accident Report Kit helps you quickly collect and report information for your company and insurance purposes.

High Stands raise the fork to a higher position. The need may arise when the suitable fork is not tall enough to reach the desired lift point, that the stinger hits the bumper before the fork is in position, or in similar situations. The high stands are 7" tall. When high stands are used, make sure the towed vehicle is secured by extra safety chains and that the "swaying motion" is limited as much as possible.

Zacklift Chain Attachment Block. A chain block assembly pins into the end of the Zacklift crossbar allowing the crossbar to be used as a truck hitch or a tie back point for safety chains. This is a great add-on for attaching chains to the Zacklift.

The Parallel motion Dolly Mount from Collins is ideal for trucks with a lower bed height. The PM-DM is designed to be loaded on the outside of the truck bed and then swings up and back to the storage position. Reduces driver fatigue and back injuries from lifting the side frames over the side of the truck bed.

Helps meet DOT's entry-level driver training requirements. Provides newly hired drivers with easy-to-understand, concise DOT compliance information. Resource works great for driver "finishing training," new hire orientation training, and drivers new to the field.

The Soft Ties from Condor help to protect your paint and chrome when tying down your bike. Use these soft ties with a heavy duty ratchet tie-down to ensure a secure bike during transport. These straps are black and are sold as pairs.

The bolt-on 15 Ton Pintle Hook from Buyers Products features tough drop-forged construction and a black powder-coated finish for maximum durability and resistance to corrosion. This versatile hook can handle towing up to 30,000 lb. Each pintle hook includes mounting information, specs sheet, drilling template, and vehicle capacity decal.

Bro Wreckers receivers have 2 fork holes for easy hook-up. The outer hole is offset and gives you extra width during axle or frame lift. Shifting one receiver from passenger side to the driver s side will decrease the distance between receivers. The receiver is a low-mount design which enables the fork to sneak under low bumpers and, when inverted, gives you extra height.

Engineered to perform together, the GUNIWHEEL 45S and the GUNIHUB are your solutions to relocating vehicles which don't want to move. Tow operators can use this portable pair for wrecked vehicles stuck in gear or locked vehicles parked in the wrong spots. Body shops can use them on barn finds or restoration projects with seized brakes.

The 8" stinger-to-trough clearance allows you to avoid air bags and low-mounted light brackets for an easy lift.

This is a trailer plate for pd75 from Diversified Products. Use this trailer plate/fifth wheel adapter to attach your chains to a trailer's king pin. The adapter is made from 1 1/4" solid steel plate, slotted to fit a 2" kin pin, and requires a pair of 1" anchor shackles. Shackles sold separately.

Made by Diversified Products Mfg., these tow slings are designed to carry the load. All Diversified tow slings are made with a heavy duty pivot design for years of trouble free operation. (Does not include chains or mount brkts)