Mobile Lifts

Replace the worn-out bed locks on your Jerr-Dan Standard Duty Car Carrier with one of these new blocks.

This is a Jerr-Dan Wheel Lift Pivot Pin Bushing. It is used on both wreckers and car carriers. This bushing is for greaseable wheel lifts. The dimensions of this bushing are 3" diameter x 2.75".

This is a Jerr-Dan latch, it is an ergo t-handle. It is for the driver's side.

This is a Jerr-Dan Wheel Lift Wear Pad for the Inner Wheel Lift Boom. The dimensions of this wear pad are, 5.94" L x 3" W x .38" H.This wear pad is used on the Jerr-Dan HPL-30 and HPL-60 Wreckers.

This is a Jerr-Dan rod, controls .75 DIA x 9.00.

The kit from Jerr-Dan comes with two pivot pins and two O rings along with the hardware needed to mount them.

This is a Jerr-Dan wheel lift pivot pin, HPL-35 & 60, Cougar.

Jerr Dan rollback wear pad kit that is compatible with AEL, RST and WAR carriers manufactured November 1991 through the current year. Also fits AWL, AVP and SVP beds manufactured October 1994 through the current year. This kit comes with all of the necessary mounting hardware and 12 total pads that have different measurements. See the features below for a list of measurements.

This is a replacement universal retaining ring from Jerr-Dan.

This Stainless Steel Paddle Latch for Jerr-Dan toolboxes holds up well to the elements.

This taillight housing features a wraparound design for the Jerr-Dan MPL wrecker body and allows lights to be seen from the rear and side. The triple bracket holds three taillights. Lights sold separately.

Jerr-Dan LED Stop / Turn / Tail Light

Jerr Dan rollback wear pad kit for 19' Jerr Dan carriers. Fits BIC (Best In Class) carriers and should be compatible with the following bed model numbers: NGAF, NGAD, NGAR, WSRB, RRSB, SLPB, NGAT, STRB, WAVB, RAYB, PAVB, ATRB, AWLB

Jerr Dan rollback wear pad kit for 20' and 21' Jerr Dan carriers. Fits BIC (Best In Class) carriers and should be compatible with the following bed model numbers: NGAF, NGAD, NGAR, WSRB, RRSB, SLPB, NGAT, STRB, WAVB, RAYB, PAVB, ATRB, AWLB

This wear pad kit is for Jerr-Dan car carriers. It fits 17' AWL (Wrangler light and old style) carriers made between 1982 and 1986. The kit comes with wear pads and hardware and includes 14 wear pads, 28 flathead machine bolts, 34 lock washers, 34 hex nuts, 2 wear pads, 4 hex cap screws, 2 nylatron pads, 2 flathead machine bolts.

Vertical Mount back up light

Mobile Lifts 6" sheave.

This is a replacement end mechanism kit.

PIN 2.25 DIA X 18.68; for underlift boom on HPL-35, HPL-60

Jerr-Dan Lug.

Jerr Dan rollback wear pad kit for 19' Jerr Dan carriers. Fits BIC (Best In Class) carriers and should be compatible with the following bed model numbers: NGAF, NGAD, NGAR, WSRB, RRSB, SLPB, NGAT, STRB, WAVB, RAYB, PAVB, ATRB, AWLB

Jerr Dan rollback wear pad kit that fits AWL, AVP and SVP carriers manufactured 1987 through September 1994.

This is a a Mobile Lifts, keyslot plate for Jerr-Dan standard, medium & 3-car carriers. It fits Jerr-Dan standard duty, medium duty and 3-car carriers.

Jerr-Dan Fork.