Search

This is a 3" right Crosstubes (wheel grids) by Miller Industries designed to fit Century 211 Crossbars.

This part can be used to replace Part Number 12-0802232.

This Outer Left Hand Crosstube Assembly fits Century Formula 6000 and 6500 Series, Holmes DFT-650 wheel lifts, and Century 20 Series car carriers. This crosstube accepts a

This Outer Left Hand Crosstube Assembly fits Century Formula 6000 and 6500 Series, Holmes DFT-650 wheel lifts, and Century 20 Series car carriers. This crosstube accepts a

Miller Industries 6,000 Lb. Tire Lift System To Fit a 4" x 4" Crossbar. Fits 1624, CH20, 4024 Wrecker Models.

Zip's Tie-Down with D-Ring measure 84" long and includes a standard ratchet with a finger hook. The webbing is abrasion resistant, and the heavy-duty hardware holds up to repeated use.

AW Direct Tie-Down with D-Ring measure 84" long and includes a standard ratchet with a finger hook. The webbing is abrasion resistant, and the heavy-duty hardware holds up to repeated use.

Miller Industries 6,000 Lb. LH Receiver To Fit a 4" x 4" Crossbar. Fits 1624, CH20, 4024 Wrecker Models.

This 84" replacement Tie-Down Strap comes with a Ratchet that has a finger hook attached to it on one end and a D-Ring attached to the other end. This strap is yellow and comes with "Zip's" printed into the webbing.

This Cotter Pin from Miller Industries is used on the Winch Clutch Control of 4-Ton Hydraulic Winches,

Also known as a wheel grid, slide bar, or receiver this 3.5" Outer Cross Tube from Miller Industries is a complete Left Hand assembly. This new style "Pivot-L" has a line-up pin and fits 3.5" x 3.5" square tubes. The cross tube fits Century, Champion, and Vulcan Car Carriers. It will accept a left hand

Also known as a wheel grid, slide bar, or receiver this 3.5" Outer Cross Tube from Miller Industries is a complete Right Hand assembly. This new style "Pivot-L" has a line-up pin and fits 3.5" x 3.5" square tubes. The cross tube fits Century, Champion, and Vulcan Car Carriers. It will accept a right hand

Miller Crossbar, Century Formula wheel lift and Century & Champion carrier wheel lifts, uses WL-300K2 pivot pin kit. Fits 1996 and older Century wreckers and 2002 and older Century and Champion Car Carriers. Use 12-0803238 for newer models.

This Inner Crosstube Weldment from Miller Industries uses a 3" x 3" square tube and has a built in trailer ball plate. It is used in the wheel lift and slide-in tire restraint assembly on Century, Challenger, Champion, Holmes, and Vulcan Car Carriers. See the brochure tab for a list of breakdowns.

This 3.5" x 3.5" square tube Crossbar from Miller Industries is used in the wheel lift assembly of Century 20 Series Car Carriers. It can also be used on Century Formula 6000 and Formula II Wheel Lifts with one piece pivot pins. See the brochure tab for a list of breakdowns.

This 3.5" x 3.5" square tube Crossbar from Miller Industries is used in the wheel lift assembly of Century 20 Series Car Carriers. I t can also be used on Century Formula 6000 and Formula II Wheel Lifts with one piece pivot pins. See the brochure tab for a list of breakdowns.

Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube Assembly from Miller Industries is a complete left hand assembly. This cross tube is used on the outer cross tube and 3-way pivot tire restraint assembly of Century and Century LCG Carriers, and Vulcan LCG Wreckers. It fits 3.5" x 3.5" square tubes and it accepts

Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube from Miller Industries is a complete right hand assembly with cam lock style plunger pins. This cross tube will fit 3.5" x 3.5" square tubes. It is used on the wheel lift and slide-in tire restraint assembly of Century, Champion, and Vulcan Car Carriers. Shop for the left hand version of this Cross Tube,

Also known as a wheel grid, slide bar, or receiver, this 3.5" Outer Cross Tube from Miller Industries is a complete left hand assembly with cam lock style plunger pins. This cross tube will fit 3.5" x 3.5" square tubes. It is used on the wheel lift and slide-in tire restraint assembly of Century, Champion, and Vulcan Car Carriers. Shop for the right hand version of this Cross Tube,

This Basket Style Strap is used to hold the tire in place, just put the strap over the tire and secure it for a tight fit. Large strap comes with one cross strap, two t-hooks attached at one end and a chain on the other. This basket strap is commonly used on Century Tow Trucks.

This OEM basket style strap is used to hold the tire in place, just put the strap over the tire and secure it for a tight fit. Large strap comes with one cross strap, two t-hooks attached at one end and a chain on the other. This basket strap is commonly used on Century Tow Trucks.

Detent kit for Century Formula 6500 wheel lifts. Helps hold the crossbar straight when not loaded. Kit includes ball, spring, and spacer.

This is a tie down strap for the cable to attach to on the Vulcan 810 and Century 211/212/311/312 by Miller Industries. This 15" rubber bungee strap will help save your boom and wheel lift from paint chips by holding your cable hook in place. See Brochures for a reference chart.

This is a hydraulic hose tensioner spring for a Vulcan 810, Century 300 Series, and Holmes 440 Series by Miller Industries. See Brochures for a reference chart and Features for related parts.

This is a front stop pin assembly for the scoop bracket weldment on Light Duty Vulcan Wreckers by Miller Industries. This stop pin w ill fit the following models: Vulcan Modular 804, Modular 806, and Modular 880/890. It works for both sides of the wrecker. This par t can be used to replace Part Numbers: 8621400 and 880411500.