Car Carrier Parts

Wheel Lift Rebuild Kit, Century Formula 6500 and Holmes DFT-650 wheel lifts. Kit includes WL-6500K1, WL-6500CPK1, WL-6500PK1, and WL-6500DK1 kits.

This Miller Industries product is a left side tail light assembly for car carriers.

Note: Special Handling Fees Apply

This Hydraulic Wheel Lift Tilt Cylinder from Miller Industries measures 3.25" x 1.75" x 13". It is designed to withstand necessary forces and to be used at stated pressures. It meets industry and government specifications and will prove itself on the job when it really matters. The cylinder is used on Century Generation II 16 Series Steel & Aluminum Carriers. Please see the features below for a list of trucks and the brochure tab for a list of breakdowns.

• Black
• 3.25" x 1.75" x 13"
  
  Fits:
• Century 16 Series Generation II LCG Steel & Aluminum Carriers 2014-Current
• Length: 23.75"
• Width: 4"

Detent kit for Century Formula 6500 wheel lifts. Helps hold the crossbar straight when not loaded. Kit includes ball, spring, and spacer.

Eagle tire adapter weldment for the wrecker crossbar.

This is a Miller Industries Control Box hood for the driver side of any Century/Vulcan Car Carrier 2005 & newer (Excluding LCG). It houses a 5-spool system and is a galvanized finish.

This Miller Industries product is a right side tail light assembly for car carriers.

This is a zinc plated 1/4"-10 Nylon Lock Nut used in the assembly of our Bearing Pad Kits.

This is a 16" long subframe bearing pad by Miller Industries. It is one of the replacement pads for a 21' Steel LCG Car Carrier. This part is included in the Bearing Pad Kit

This Heat Shrink Tube, or Scuff Jacket, seals and protects cable splices, terminations, and bed hoses. This jacket is suitable for a variety of low-voltage electrical and mechanical applications, where lightweight and flexibility are important. This tube can be used on the Hydraulics Assembly of Century and Vulcan Car Carriers. See the features below for a full list of carriers and see the brochure tab for breakdowns. This part can be used to replace Part Number 12-0303193.

This Cross Tube Pivot Pin from Miller Industries is used in the wheel lift assembly of Century 20 Series Car Carriers. The pivot pin goes on top of the inner cross bar weldment during assembly. Please see the brochure tab for breakdowns.

Pivot Pin Kit for Holmes DFT-200 wheel lift. Kit includes (1) GR-63 Pivot Pin, (1) GR-232 Pivot Pin Bushing, (1) GR-50 Pivot Pin Retainer Plate, and (2) DE-524 Button Head Screws.

Blade rails used on front of 19' & 21' by MIller Industries.

This wear pad kit is for Jerr-Dan car carriers. It fits 17' AWL (Wrangler light and old style) carriers made between 1982 and 1986. The kit comes with wear pads and hardware and includes 14 wear pads, 28 flathead machine bolts, 34 lock washers, 34 hex nuts, 2 wear pads, 4 hex cap screws, 2 nylatron pads, 2 flathead machine bolts.

Note: Special Handling Fees Apply

This is a tie down strap for the cable to attach to on the Vulcan 810 and Century 211/212/311/312 by Miller Industries. This 15" rubber bungee strap will help save your boom and wheel lift from paint chips by holding your cable hook in place. See Brochures for a reference chart.

This is a warn winch replacment freespool spring.

This is a Wiring Harness for the Century 22'

This Clutch Housing from Ramsey Winch is used in the assembly of 4-Ton Hydraulic Winches,

Pivot Pin Kit, Challenger I-600 wheel lift. Includes (1) 12-0802352 Pivot Pin, (1) 12-0302248 Pivot Pin Bushing, (2) Thrust Washers, and (1) 12-0400278 Pivot Pin Retaining Bolt.

This is a Miller Industries tail light face plate for the left hand side of any LCG Car Carrier. It is available in stainless steel. The light configuration is horizontal.

This is a Century oil reservoir, without immersion oil filter, for 10, 12, or 15 series carrier. Mounts on back side of optional toolbox/outside of chassis frame. This part replaces part number 12-0805237.

This is a wear pad holder on the up/down portion of the wheel lift by Miller Industries. It is bolted on by tow bolts and there are 2 wear pad holders per wheel lift. This wear pad holder fits the following wreckers: Vulcan 880/890, Modular 880/890 and 896/897. See Features for related hardware and Brochures for reference charts.