Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
Car carriers and rollbacks do not make any money when their sidelined with a breakdown. Get your equipment back to work again with quality replacement parts from Zip’s AW Direct. We stock cylinders, winch drums, control assemblies and other essential hardware to facilitate your repair. We also have the necessary lighting, wiring and brackets to make sure you’re seen when you’re back out on a job.
This zinc-plated mild steel L-Arm from Miller Industries fits the driver side of the wheel lift on Vulcan 896 and 897 medium-duty wreckers. Otherwise known as a tire restraint or wheel retainer, the 2" x 3" rectangular tube fits the 12-4008001 outer crosstubes and offers adjustment holes and a grated tire scoop pan for tire securement.
Outer Crosstube assembly, left hand, New style "Pivot-L" with line-up pin, fits Century Formula 6000 & 6500 and Holmes DFT-650 wheel lifts. Accepts 12-0904156 light weight aluminum L-arm. This part can be used to replace Part Number 12-0902790.
Fits 3 1/2" x 3 1/2" square tube
Century new style "Pivot-L" with line-up pin
Uses 12-0902382 basket strap
Can also be used on Century/Champion 20 series car carriers
This is a wear pad cage plate on the inside, bottom of the outer boom of a Century Formula I 411/412, and a Century 6500 600 Series Wrecker. This cage plate also fits Challenger 4700 and 4800 Series Wreckers. It will also fit Holmes 440 Series and HP552 Series by Miller industries. See Brochures for a reference chart and Features for related parts. This part can be used to replace Part Number 12-0703093.
This is a Bearing Pad Kit by Miller Industries. It includes all the parts necessary to replace the wear pads on a 21'6" & 22'2" Stee l Car Carrier. See Features for a list of parts that are included.
This Miller Industries product is a full assembly of the right side of a tail light section on a car carrier. It is designed for Vulcan Car Carriers. It includes all the necessary parts to replace the entire tail light section this product bolts into the mounting bracket which is attached to the subframe of the carrier.
This is a wear pad retainer plate on the up/down portion of the wheel lift by Miller Industries. It is bolted on by 3 bolts. This retainer plate fits the following wreckers: Vulcan 880/890, Modular 880/890, and 896/897. See Features for related hardware and Brochures for reference charts.
This Miller Industries product is a full assembly of the left hand side of a tail light section on a car carrier. It is designed for Vulcan Car Carriers. It includes all the necessary parts to replace the entire tail light section. This product bolts into the mounting bracket which is attached to the subframe of the carrier.
This is a Miller Industries work light mounting bracket to be installed on a car carrier tail light board. It is designed to be installed on any LCG car carrier.
This pivot-style L-Arm from Miller Industries fits Formula 6500 wheel lifts on Century wreckers. Also known as a tire restraint or wheel retainer, option of driver or passenger side L-Arm fits 2 x 3 outer crosstubes (Part Nos. 12-0904158 and 12-0904189). This zinc-plated L-Arm also features an alignment hole on the underside and includes a ratchet tie-down strap.
This is a replacement air valve toggle guard by Chevron. This guard is used to protect the toggle switch used to operate an air valve on your car carrier bed.
This Pivot Pin Kit is for a Century Formula I early style wheel lift. The kit includes one 12-0301486 snap ring, one 12-0306748 bronze bushing, one 12-0702141 pivot pin, and two 12-0703640 thrust washers.
Can't find where the broken wire is to your taillights? Replace the wiring with this harness from Miller Industries. This part can be used to replace Part Nos.: 12-0301803 and 12-0301804.
Jerr Dan rollback wear pad kit for 19' Jerr Dan carriers. Fits BIC (Best In Class) carriers and should be compatible with the following bed model numbers: NGAF, NGAD, NGAR, WSRB, RRSB, SLPB, NGAT, STRB, WAVB, RAYB, PAVB, ATRB, AWLB
This Coupler from Miller Industries is used in the assembly of a 4-ton hydraulic winch. This winch is used on many Miller Car Carriers, including Century, Challenger, Champion, Holmes, and Vulcan Carriers. See the features below for a full list of carriers that this winch is used on. Also see the brochure tab for a list of breakdowns.
This 3/4" Red Marker Light from Miller Industries comes with a Grommet. It is used for the rear marker lights on Century 10 Series Carriers and 16 Series LCG Gen II Carriers. See the brochure tab for breakdowns.
This Tail Light Housing has three holes plus a marker light hole. It is made from stainless steel, so it will last for years. This housing replaces old style heavy duty light housings.
This is a replacement pivot pin for Century and Holmes Autoload wreckers by Miller Industries. This pivot pin will fit the Century Modular Midnight Express, Holmes 220 Snatcher, and 440SL light duty wreckers. To view part schematics please click on the Brochures tab.
This is a replacement fluid tube for a LCG Car Carrier by Miller Industries. This tube connects the winch motor to the under body line beneath the bed of the car carrier.