Century

This is a replacement valve double holding.

Note: Special Handling Fees Apply

This is the Lift Cylinder on the Wheel Lift of Century Wreckers with the Formula I and Formula 6500 Wheel Lifts. It is used on the Century Formula 6500 - 600 Series and the Modular 400 & 600 Series with these wheel lift options. To view part schematics click the Brochure tab.

• Uses holding valve part number 12-0304567
  
  Fits:
• Century Formula 6500, 600 Series REV A
• Century Modular 400 & 600 (01/2009 - Current)

This is a Miller bracket handle used on Husco valves. This piece bolts onto the valve assembly itself and is used to hold the control rod linkage to the valve. It acts as the pivot point to for the control rod to operate the valve.

This washer has been replaced by Part Number 39873. This General Purpose Flat Washer can be used on most Miller Carrier and Wrecker assemblies, including Century, Challenger, Champion, Eagles, Holmes, and Vulcan. Flat washers are typically used under the head of a bolt of nut to distribute the forces applied when tightening. The zinc plating greatly decreases the corrosion rate. Please refer to the Parts Schematics page for lists of breakdowns.

This is a replacement toolbox center bonded mount.

This is the outer tube shim pad for the side, inside of the wheel lift by Miller Industries. This Shim Pad will fit the following wreckers: Century Modular Express 300 Series, Modular Midnight Express, Modular 400 & 600 Series, Holmes 440SL, Vulcan Modular 806, Modular 807, 812 Intruder, and Modular 880/890. See Brochures for reference chart and Features for related hardware. Each pad sold separately.

This is the Wheel Lift Extend Cylinder Base End Pin for Century Modular Midnight Express and Modular 211's. This pin also will fit Holmes 440SL, Vulcan Modular 804, 806, and 807 wreckers. It will also work with the Vulcan 810 Power Tilt light duty wrecker by Miller Industries. To view specific models see Features below. To view part schematics click the Brochure tab.

This Bottom Half Pivot Pin from Miller Industries is used in the assembly of many Miller Wreckers. These include Century, Challenger, and Holmes Wreckers. The bottom half pivot pin is attached on the bottom side of the crossbeam weldment. Please see the brochure tab for a list of breakdowns.

This is the base lift cylinder pin on the wheel lift of Century, Challenger and Holmes wreckers by Miller Industries. This pin replaces part number 12-0801012. This cylinder pin will fit the following wreckers: Century Formula I - Duplex Tilt 411 & 412, Formula I - Duplex Tilt Super Six & 500, Formula 6000 - 600 Series, Formula 6500 - 600 Series, Metro I - Duplex Tilt, Challenger 4700 Series, and the Holmes 440 Series. To view year ranges see Features below. To view part schematics click on the Brochures tab.

This is a replacement 5/8" Camlock.

This is a Air Solenoid from Motion Industries.

This is a 36" 10 series wear pad from Miller Industries.

This is a replacement wheel lift upper arm pin weldment on Light Duty Century and Holmes Wreckers by Miller Industries. This pin attaches the wheel lift upper arm weldment to the outer boom weldment of the wheel lift. This pin fits the Century Formula 6500, 600 Series and Modular 400 & 600 Series. It will also fit the Holmes HP 552/DFT 650 wrecker. To view the part schematics please click the Brochures tab.

This is a replacement 2Spd Dp stem.

This is a replacement 5 Spool Parker Control Valve for the Vulcan 810 Auto-Load and the Century Modular Midnight Express light duty wreckers by Miller Industries. To view part schematics please click on the brochure tab above. This part can be used to replace part number 12-0306776.

This clevis pin measures 5/16" x 1". To view part schematics click on the Brochure tab.

This is a hydraulic hose tensioner spring for a Vulcan 810, Century 300 Series, and Holmes 440 Series by Miller Industries. See Brochures for a reference chart and Features for related parts.

This Bushing from Miller Industries is used on the Wheel Lift and Under Lift Assembly of several Miller Wreckers. These include Century, Challenger and Holmes Wreckers. The Bushing measures 3.75" tall with an outside diameter of 4" and an inside diameter of 3.5", giving it an overall thickness of .25". Please see the features below for a list of wreckers and see the brochure tab for breakdowns.

This is a Bearing Pad Kit by Miller Industries. It includes all the parts necessary to replace the wear pads on a 17'6" & 19' Aluminum Car Carrier. See Features for a list of parts that are included.

This Screw from Miller Industries is used to hold the pin weldment in place on the boom, wheel lift, underlift, and tower assemblies of many Miller Wreckers. These include Century, Challenger, Holmes, and Vulcan Wreckers. The screw measures 3/8" x 5/8" and has a thread size of 24. Please see the brochure tab for a list of breakdowns.

This is a replacement breather vent 1/8 Mp from Miller.

This Red LED Marker Light from Miller Industries is used on Century, Century LCG, Champion, and Vulcan Car Carriers. The light measures 5-1/2" long and 1" wide. It also comes with a gasket, pigtail and bulb.

This Pigtail from Miller Industries is used with a Hella Work Lamp.