Car Carrier Parts

Pivot Pin Kit for Vulcan 850 and 890 wheel lifts.

Update the wiring for the exterior DOT lighting on your Century car carrier with this new harness from Miller Industries. Wiring fits up to 21'6" decks. Replaces 0302217.

This is a Miller Industries control rod end cap. Instead of cotter pins, these end caps hold the control rods in place within the control assembly.

These are the wear pads for the inner and outer booms of the wrecker. These Wear Pads will fit the following wreckers by Miller Industries: Century Express 300 Series, EB4 Express, EB4 6500, Modular Express 300 Series, Formula I, Duplex Tilt 411 & 412, Formula 6500 - 600 Series, Midnight Express, Challenger Express 4300 Series, 4700 Series, 4800 Series, Holmes 440 Series, DFT 400, HP 552, DFT 650, and Vulcan Modular 806 and 807. See Brochures for reference chart . Each Wear Pad sold separately.

This Miller Industries product is the right hand side tail light housing for Century or Vulcan 10, 15, 20 or 30 Series Car Carriers 2005-Current. Its painted black steel shell houses all the right hand side tail light components, as well as the face plate. It bolts onto the mounting bracket (12-0710783) which is attached to the subframe of the carrier. See features for additional information. This part can be used to replace Part Number 12-0801574.

This is a pivot shaft for an L-Arm Bracket to the crosstube on the Century 211 by Miller Industries. See Brochures for a reference chart.

This Miller Industries product is the left hand side tail light housing for Century or Vulcan LCG Series Car Carriers (Generation I or II). Its painted black steel shell houses all the left hand side tail light components, as well as the face plate. It bolts onto the mounting bracket (12-0710783) which is attached to the subframe of the carrier. See features for additional information.

This Hex Jam Nut from Miller Industries has a 1/2" diameter with 13 threads per inch. It isused on the Winch Clutch Control of 4-Ton Hydraulic Winches, H-246 and HD-200R. This winch assembly is used on several Miller Car Carriers, including Century, Challenger, Champion, Holmes, and Vulcan Carriers. See the features below for a full list of carriers. Also see the brochure tab for a list of breakdowns.

Note: Special Handling Fees Apply

This is a 96" long subframe bearing pad by Miller Industries. It is one of the replacement pads for a 2010 or newer 10 Series Car Carrier. This part is included in the Bearing Pad Kit <a href="http://zips.com/parts-detail/miller- bearing-pad-kit-10s-%2710-newer-12-0940278"target="_blank"/> 12-0940278</a/>.

• 5/16"x96" Subframe Pad
• 2010 & Newer 10 Series Car Carriers

This Miller Industries product is the left hand side tail light housing for Century or Vulcan 10, 15, 20 or 30 Series Car Carriers 2005-Current. Its painted black steel shell houses all the left hand side tail light components, as well as the face plate. It bolts onto the mounting bracket (12-0710783) which is attached to the subframe of the carrier. See features for additional information. This part can be used to replace Part Number 12-0801573.

This is a spacer bar that is located on the top, inside of the wheel lift outer stinger weldment by Miller Industries. This spacer bar will fit on the following wreckers: Vulcan 880/890, 805, 806, Modular 880/890, 896/897. See features for related hardware and see brochures for reference charts.

This is an outer tube Spacer pad for the wheel lift the Century and Vulcan car carriers. It is a spacer pad for (2) Bearing Pads (Part# 12-0750505) mounted on the inside of the outer tube on the wheel lift.

If the four-spool hydraulic control valve on your Miller Industries car carrier is not as responsive as it once was, service it now with a new spool valve repair kit from Parker. The replacement parts will ensure the neutral spring will bring your levels back to center each time. The valve is used on Miller 10 (prior to 2001) and Miller 30 (2005 to present) series car carriers as well as on most twin line Century/Vulcan wreckers.

This is Miller Industries bracket to connect the control handle to the valve body within the control assembly of a carrier.

Note: Special Handling Fees Apply for Specific Items

These 102" wide Car Carrier Pylons are used with Miller Century, Champion, Challenger, Holmes, and Vulcan 10 Series Rollbacks. They fit 12, 15, and 16 LCG Series beds. These frame mounted light pylons are available with a 5" x 5" or 8" x 6" base. They also come in a variety of heights from 32" to 68". Car Carrier Pylons are commonly used as cab protectors. See application chart under the brochures tab.

• Cab Protector for 10 Series Rollback Carriers
• Fit 12, 15, and 15 LCG Series beds
• Frame Mounted
• 102" wide
• Heights from 32" to 68"
• Available in 5" x 5" or 8" x 6" base
• Painted black
• Includes safety chain tie back
• Hollow tube for wiring

This is a stainless steel tail light face plate for the right hand side of the Century Generation II LCG car carriers. The light configuration for this bezel is horizontal. Does not include lights or license plate mounting hardware as pictured in photo. All that is included is the stainless steel face plate.

Towbar spring for Eagle wheel lifts. This spring is used to hold the towbar straight when the wheel lift is unloaded. Attatches to the towbar and to the inner stinger.

This Immersion Filter Assembly from Miller Industries replaces the old 9018307 assembly. The filter is used on the hydraulics assembly of Vulcan 10 Series Extreme Angle Carriers and the pump, valve and filter hydraulics of Vulcan 807 Modular Wreckers. This filter is also used on the hydraulics assembly of Century 15 Series 2 and 3 Car Carriers and Century 20 Series 2, 3 and 4 Car Carriers.

This seal kit fits, Century, Holmes, and Champion Wheel-lift In/Out cylinders afer December 2002. It is a universal kit that will fit Texas (marked TH) ot Green manufactures cylinders. Please remember that seal kits may fit different c ylinders of the same diameter. See the chart below for more information. This part can be used to replace Part Numbers: 12-0308388 and 12-0308896.

Add more functionality to your SafeAll Proportional Remote Control System by installing additional actuators on your car carrier's hydraulic linkages. Each sealed actuator features a rugged, weatherproof shell to withstand harsh road conditions. Bluetooth technology aids in actuator synhronization and calibration. If you want to incorporate additional functionality of controls at a later date, simply purchase individual actuators "a la carte."

This is an aluminum bronze bushing for a wheel lift pivot pin on a Vulcan 807 by Miller Industries.

This Miller Industries product is the right hand side tail light housing for Century or Vulcan LCG Series Car Carriers (Generation I or II). Its painted black steel shell houses all the right hand side tail light components, as well as the face plate. It bolts onto the mounting bracket (12-0710783) which is attached to the subframe of the carrier. See features for additional information.

Note: Special Handling Fees Apply

This Wheel Lift Extend Cylinder from Miller Industries is used on the Hydraulics Assembly of several Miller Car Carriers. These include Century, Challenger, Champion, Holmes, and Vulcan Carriers. See the features below for a full list of carriers and see the brochure tab for breakdowns.

• Standard color is black
• Uses Seal Kit 12-0306134
  Fits:
• Century 10 Series Steel & Aluminum Carriers
• Century 15 Series Steel & Aluminum Carriers
• Century LCG 12 Series Steel & Aluminum Carriers
• Century LCG 16 Series Steel & Aluminum Carriers
• Challenger Car Carriers
• Champion Steel & Aluminum Carriers
• Holmes 10 Series Steel & Aluminum Carriers
• Vulcan 10 Series Steel & Aluminum Carriers
• Vulcan 10 Series Extreme Angle Steel Carriers

This Spring from Ramsey Winch is used in the assembly of 4-Ton Hydraulic Winches,

This is a stainless steel tail light face plate for the left hand side of the Century Generation II LCG car carriers. The light configuration for this bezel is horizontal. Does not include lights or back up alarm pictured in photo. All that is included is the stainless steel face plate.