Light Duty Wrecker Parts

This is the Boom Lift Cylinder Upper Pin for Century 614 Series light duty wreckers by Miller Industries. This pin goes through the rod end of the lift cylinder. This pin connects the boom lift cylinder to the outer wrecker boom weldment allowing the cylinder to pivot as the boom goes up and down. To see which models this pin will fit please see Features below. To view part schematics click on the Brochure tab.

This Seal Kit is for part 8603000. This part can be used to replace Part Number, 8616800.

This is the Upper Cylinder Pin on the Lift Cylinder on Century Formula I Duplex Tilt 411 & 412 wreckers. This pin also fit the Century Formula 6000 - 600 Series wrecker. To view part schematics click on the Brochures tab.

This 2.5" Fender Flare from Phoenix USA for a 1993 - Current Jerr-Dan Steel Body Wrecker will add the finishing touch to your wrecker. It is for the left, rear fender on your wrecker body and it will give you a clean custom look. It will provide excellent tire coverage on the rear tires. The flare will help keep mud and debris from being thrown onto a nice paint job or on the vehicle you are towing. The addition of fender flares will help the truck comply with certain state tire exposure regulations. Sold as each (One Left Rear).

This aluminum diamond plate dress-up kit from Miller Industries is for the inside of the 124002343 steel light pylon. This trim panel covers the back side of lights and wiring.

Vulcan 896/897 4.5" x 4.5" Wheel Grid for the Driver Side.

This is the Hair Pin for the Boom Lift Cylinder Pin BK-518. This hair pin keeps the clevis pin from pulling out and letting the cylinder fall off the boom.

This is the Wrecker Boom Extend Cylinder Pin for the Vulcan 896 and 897 Series light duty wreckers by Miller Industries. This cylinder pin goes through the rod end of the cylinder. This pin connects the boom extend cylinder to the wrecker inner boom weldment. To view the part schematic click on the Brochure tab.

This Miller Industries product is a replacement cable follower.

Replacement diverter valve cable for Century add-on wheel lifts.

This is a 1" Heavy Duty extended retaining / snap ring that is used on the boom and underlift of wreckers.

This is the Wrecker Boom Extend Cylinder Pin for the Vulcan 880 / 890 Series and the Vulcan 806 Series light duty wreckers by Miller Industries. This pin is used to secure the boom extend cylinder to the inner wrecker boom weldment. To view the part schematic click on the Brochure tab.

This is the Wrecker Boom Lift Cylinder Pin for the Holmes HP 552 light duty wrecker by Miller Industries. This pin goes through the rod end of the cylinder. This pin is used to connect the boom lift cylinder to the outer wrecker boom weldment. To view the part schematic click on the Brochure tab.

This is a Seal Kit for the Lift Cylinder on the Century Formula II Wrecker by Miller Industries. To view part schematic click the Brochures tab.

This is a Wheel Lift Tilt Cylinder Pin for the Formula I Wheel Lift Assembly on the Century Modular 400 & 600 Series light duty wrecker by Miller Industries. This pin is used to connect the tilt cylinder to the outer boom stinger weldment of the wheel lift. To view the part schematic click on the Brochure tab.

This is the Fold Cylinder Lower Pin for the rod end of the Cylinder on Century Modular 211, Vulcan Modular 804 and Modular 806 light duty wreckers by Miller Industries. This is the pin that connects the fold cylinder to the wheel lift of the wrecker. To see which specific wrecker models this pin will fit please see Features below. To view part schematics click on the Brochure tab.

This 2.5" Fiberglass Fender Flare from Phoenix USA for a Challenger 4800 body will add a custom look to your wrecker. It will also provide excellent coverage over your rear tires. The flares keep mud and debris from being thrown onto a nice paint job or on the vehicle that you are towing. The addition of fender flares will help the truck comply with certain state tire exposure regulations. Sold as Each.

This is a Boom Lift Cylinder Pin for the boom of the Century Midnight Express by Miller Industries. This is the rod end pin for the lift cylinder. This pin is used with lift cylinder part number, 12-0306658. To view the part schematic click the Brochure tab.

This 3" wide Fender Flare from Phoenix USA for a Challenger 4700 and Holmes 460 body will add a custom look to your wrecker. It will also provide excellent coverage over your rear tires. The flares keep mud and debris from being thrown onto a nice paint job or on the vehicle you are towing. The addition of fender flares will help the truck comply with certain state tire exposure regulations. Sold as Each.

This is the Wheel Lift Tilt Cylinder for the Vulcan 805 Series light duty wrecker by Miller Industries. This is the cylinder that tilts the wheel lift of the wrecker up and down. This cylinder attaches to the wheel lift outer boom weldment and the wrecker outer boom weldment. To view the part schematic click on the Brochure tab.

These are Spry Master injection molded polypropylene full fenders. These are more durable and forgiving than aluminum fenders plus they won't corrode. Sold as pairs.

This is the hydraulic hose tension track bracket on the Century 300 Express, EB4 Express, and Challenger 4300 Express Series by Miller Industries. See Brochures for part schematics and Features for related parts and to see what models this fits.

24" Tall Steel Light Pylon from Miller Industries. Installation includes a plastic isolator between the pylon and the body. This light pylon fits Chevy 3500's with tunnel toolbox.

This is the Lift Cylinder for the Formula II Wheel Lift on the Century 614 light duty wreckers by Miller Industries. This lift cylinder has a 5" Bore. This is the cylinder that lifts the boom of the wheel lift up and down. To see which specific models this lift cylinder will fit please see Features below. To view part schematics click on the Brochure tab.

This is the Wheel Lift Extend Cylinder Pin on the Challenger 4800 Series light duty wreckers by Miller Industries. This pin goes through the rod end of the extend cylinder. This pin connects the wheel lift extend cylinder to the inner wheel lift boom weldment. To view the part schematic click on the Brochure tab.