Light Duty Wrecker Parts

Control Cables by CableCraft. Replacement Push-Pull Control Cables for Holmes and Century uses.

There are wreckers and older equipment that still require the use of Boom Support lines. These cables from All-Grip are the same as factory replacements. Constructed of 6 x 19 Eip Fibercore wire rope with a flemished thimbled eye at one end while the other end is plain.

This is the Wrecker Boom Lift Cylinder for the Vulcan 880 / 890 and 896 / 897 Series light duty wreckers by Miller Industries. This cylinder attaches to the outer wrecker boom weldment and the subframe of the wrecker. This cylinder raises the boom of your wrecker up and down. This cylinder can also be referred to as the boom elevation cylinder. To see which specific models this lift cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Wheel Lift Extend Cylinder for Century 712 & 716 Series light duty wreckers by Miller Industries. This Cylinder connects the inner and outer wheel lift boom weldments together allowing the wheel lift boom to slide in and out. To view the part schematic click on the Brochure tab.

This is the Lift Cylinder Pin on the I-600 Wheel Lift on the Challenger 4800 Series light duty wreckers by Miller Industries. This pin goes through the base end of the lift cylinder. This pin connects the lift cylinder to the wheel lift frame weldment. To view the part schematic click on the Brochure tab.

Note: Special Handling Fees Apply

This is the Boom Lift Cylinder on the Century 411 and 412 Series wreckers. It will also fit on the Vulcan Modular 880 and 890 Series light duty wrecker by Miller Industries. This is the cylinder that raises the boom of your wrecker up and down. It is also sometimes called the Boom Elevation Cylinder. To view specific wrecker models this cylinder will fit please see Features below. To view part schematics click on the Brochure tab.

<pre/>Fits:

Century Modular 400 & 600 (01/2009 - Current)

Vulcan Modular 880 / 890 (06/1999 - Current)

</pre/>

Prevent cable kinking and flat spots on your wire rope with these Sheave Wheels. Featuring heavy-duty cast iron construction and self-lubricating bronze bushings for long life and low maintenance.

This is the Lift Cylinder for the Wheel Lift on the Century 712 & 716 Series light duty wreckers with a Formula III wheel lift. This is the cylinder that raises your wheel lift boom up and down. This cylinder replaces part number 12-0303101 (which is no longer available).

This is a replacement cylinder for the rear stabilizers on a Chevron Renegade 408 model wrecker.

This is the Wheel Lift Extend Cylinder for the Wheel Lift on the Century Midnight Express and Modular Midnight Express Series. To view wrecker models this cylinder will fit see Features below. To view part schematics click on the Brochures tab.

This Plunger Pin from Miller Industries is used on the Subframe Assembly of Holmes DTU Generation II Wreckers. See the brochure tab for a breakdown.

This is a Boom Wing Cable Guide Kit from Zip's Truck Equipment. These wing cable guides will help guide the winch cable from the boom end back to the winch without it hanging down and scratching up your boom. This kit consists of 2 boom wings, one measures 13" and the other measures 16" long.

This is the Tilt Cylinder on the Holmes DFT-200 Wheel Lift by Miller Industries. This is the cylinder that tilts the wheel lift on your wrecker up and down. This cylinder has a 5" bore. This part can be used to replace Part Number GR-3C.

This is the Boom Lift Cylinder Base Pin on the Century Modular 211, Vulcan Modular 804 and Vulcan Modular 806 light duty wreckers by Miller Industries. This pin connects the Boom Lift Cylinder to the subframe assembly. To view specific wrecker models please see Features below. To view part schematics click on the Brochure tab.

This is the Wrecker Boom Lift Cylinder for the Vulcan 805, Vulcan 806, and Vulcan 807 Auto Grip light duty wreckers by Miller Industries. This is the cylinder that raises the wrecker boom up and down. This cylinder attaches to the wrecker subframe weldment and to the wrecker outer boom weldment. This cylinder is also referred to as the boom elevation cylinder. To see which specific wrecker models this cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Boom Lift Cylinder on Century Modular 211, Modular 400 & 600, Vulcan Modular 804 and Vulcan Modular 880 / 890 light duty wreckers by Miller Industries. This lift cylinder has a 3.5" bore and a 17.75" stroke. This is the cylinder that raises the boom of your wrecker up and down. To view specific wrecker models please see Features below. To view part schematics click on the Brochure tab.

This is the Wheel Lift Extend Cylinder Pin on the Challenger 4800 Series light duty wreckers by Miller Industries. This pin goes through the base end of the extend cylinder. This pin connects the wheel lift extend cylinder to the outer wheel lift boom weldment. To view the part schematic click on the Brochure tab.

This is the Boom Extend Cylinder for wrecker booms on light duty wreckers by Miller Industries. This extend cylinders has a 2.5" Bore and a 60" Stroke. This cylinder will fit on Century Formula I Duplex Tilt 411, 412, Super Six, and 500 Series, Century Formula 6000 - 600 Series, Century 614 FIIT Wrecker, Challenger 4700 and 4800 Series, and Holmes 440 Series. To view specific wrecker models see Features below. To view part schematics click the Brochures tab.

This Miller Industries product is a replacement tieback kit.

This is a Seal Kit for the Wheel Lift Extend Cylinder on the Century 712 & 716 Series light duty wreckers by Miller Industries. This seal kit is used on extend cylinder part number, HD130. To view the part schematic click on the Brochure tab.

This is a Boom Lift Cylinder for wrecker booms on Century and Holmes Light Duty Wreckers by Miller Industries. This lift cylinder will fit the Century Formula I Duplex Tilt 411 and 412, and the Holmes HP 552 / DFT 650. This cylinder replaces cylinder part numbers: 12-0302218 and 12-0302356. To view part schematics click the Brochures tab.

This Bushing from Miller Industries is used on Wheel Lift Tilt Cylinder

This is a Boom Lift Cylinder Pin for the boom of the Century Midnight Express by Miller Industries. This is the base end pin for the lift cylinder. To view the part schematic click the Brochure tab.