Century

This is a Miller Industries Control Box hood for the driver side of any Century/Vulcan Car Carrier 2005 & newer (Excluding LCG). It houses a 5-spool system and is a galvanized finish.

This is a 3/8-16 X 1.25 Hhcs Gr5 Zp from Miller Industries.

This is a replacement pigtail cable.

This is a replacement Miller slide pad - Nylatron.

This Miller Industries product is a right side tail light assembly for car carriers.

This is a replacement 3-Stage Boom Extended Cable Assembly for use with Century trucks.

This is a zinc plated 1/4"-10 Nylon Lock Nut used in the assembly of our Bearing Pad Kits.

Quick release spring used with the quick release pin. This spring keeps tension on the quick release pin, which keeps the straps/chains from loosening.

This is a 16" long subframe bearing pad by Miller Industries. It is one of the replacement pads for a 21' Steel LCG Car Carrier. This part is included in the Bearing Pad Kit

This is the Lower Cylinder Pin on the Lift Cylinder on Century Formula I Duplex Tilt 411 & 412 wreckers. This pin also fit the Century Formula 6000 - 600 Series wrecker. To view part schematics click on the Brochures tab.

This Heat Shrink Tube, or Scuff Jacket, seals and protects cable splices, terminations, and bed hoses. This jacket is suitable for a variety of low-voltage electrical and mechanical applications, where lightweight and flexibility are important. This tube can be used on the Hydraulics Assembly of Century and Vulcan Car Carriers. See the features below for a full list of carriers and see the brochure tab for breakdowns. This part can be used to replace Part Number 12-0303193.

This Cross Tube Pivot Pin from Miller Industries is used in the wheel lift assembly of Century 20 Series Car Carriers. The pivot pin goes on top of the inner cross bar weldment during assembly. Please see the brochure tab for breakdowns.

This Plunger Spring from Miller Industries is used on the Wheel Lift Assembly of Century 20 Series Car Carriers made between 2002 and 2006. The spring is 3-1/4" long. See the features below for a full list of carriers and see the brochure tab for breakdowns.

This is a replacement seal kit for part number 12-0306674.

This Tailboard Dress Up Kit from Miller Industries can be used on Vulcan V-70 and V-100 trucks.

This Cotter Pin from Miller Industries is used on the Winch Clutch Control of 4-Ton Hydraulic Winches,

This is a tie down strap for the cable to attach to on the Vulcan 810 and Century 211/212/311/312 by Miller Industries. This 15" rubber bungee strap will help save your boom and wheel lift from paint chips by holding your cable hook in place. See Brochures for a reference chart.

This is a Miller O-ring, pivot pin. It is a Century SDU.

This is a 6Mj-6Mb fitting connector from Miller.

This 3/4" Flat Washer from Miller Industries is used on several different applications on many different Car Carriers and Wreckers. The washer is used on the assembly of Century and Vulcan 10 Series Carriers. It is also used on Century, Challenger, Champion, Holmes and Vulcan Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdowns.

This is a Wiring Harness for the Century 22'

This is a replacement washer special .406ld X 1.75Od.

This is a fold cylinder clevis pin.

This is the Fold Cylinder Upper Pin for the base end of the cylinder on Century Modular 211, Vulcan Modular 804, Modular 806 and Modular 807 light duty wreckers by Miller Industries. This is the pin that connects the fold cylinder to the boom of the wrecker. To see which specific models this pin will fit please see Features below. To view part schematics click on the Brochure tab.