Century

This is a Miller Industries Control Box hood for the driver side of any Century/Vulcan Car Carrier prior to 2005 (Excluding LCG). It houses a 5-spool system and is a steel finish.

This is a replacement control cable for Century and Challenger Heavy Duty Wreckers. This control cable is 114" long and has a 1" stroke. Please see Features for what models this control cable will fit.

This Rubber T Mount from Miller Industries is used on the Subframe Assembly of many Century, Eagle, Holmes, and Vulcan Wreckers. Please see the brochure tab for a full list of breakdowns.

This is a replacement 21" LED Vista Light. This part can be used to replace Part Number 12-0310217.

This is the rear extend cylinder pin for many light duty wreckers by Miller Industries. This pin will work with most Century, Challenger, Champion, Holmes and Vulcan light duty wreckers. This pin measure 6" long with a diamter of 7/8". To view specific wrecker models this pin fits see Features below.

This is a Miller Industries Control Box hood for the passenger side of any Century/Vulcan Car Carrier prior to 2005 (Excluding LCG). It houses a 5-spool system and is a steel finish.

This is an inner & outer tube bearing pad for the wheel lift of a Century or Vulcan LCG Series car carrier. There are a total of 4 bearing pads for each equipped wheel lift. See Features for which years/models they are used on.

This is the L-Arm side, Swing L-Arm Cylinder Pin. This pin fits cylinder part number 12-0303844. This pin fits Century, Challenger and Vulcan wrecker models. To view specific models see Features below. To view part schematics click on the Brochures tab.

Miller Industries' winch loop harness assembly for 17', 16' and 19' Century, Champion and Vulcan carrier beds.

This Latch Paddle from Miller Industries comes with a rubber gasket. It is used on the toolbox that is used on the body assembly of several Miller Wreckers. These include Century, Holmes, Eagles and Vulcan Wreckers. Please see the features below for a list of Wreckers, and see the brochure tab for breakdowns.

This Spring from Miller Industries is used on a Crossbar.

This is a Hose Tray used on 21' bed car carriers by Miller Industries. This hose tray is 9' long x 3.5" wide. The channel where the hose lays in is 2" wide. This hose tray will fit 21' beds from Century, Champion and Vulcan. See Features Below to see which models it will fit. This part can be used to replace Part Number 12-0720283. This part will be cut into three sections in all cases for economical shipment.

This 1-3/16" steel Detent Ball from Miller Industries is used on the assembly of Century Car Carriers and Wreckers.

This Air Cylinder from Miller Industries has a 1.5" Bore and a 1.71" Stroke. This cylinder is used on the assembly of many Century Wreckers, including 11075S/SDU4 Wreckers, 1140/1130/SDU4/LDU Wreckers and 1040B/SDU3 Wreckers. It is also used on the assembly on Challenger 9909 and 8808 Rotators.

This is a Miller Industries Control Handle Knob. It is black in color and is used on a 2005 or older Series car carriers.

This is the front extend cylinder pin for the wheel lift extend cylinder on Miller Industries Light Duty Wreckers. It replaced part number 12-0703345. To view what models this pin fits on please see Features below. To view part schematics click on the Brochures tab.

This Thrust Washer from Miller Industries has a diameter of 10" and a thickness of 1/8". It is used on many different Miller wrecker assemblies, including, SDU, LDU, Underlift, and Tower assemblies on Century, Challenger, and Holmes wreckers. Please see the brochure tab for a list of breakdowns.

This is a Miller Industries Control Handle Knob. It is black in color and it is labeled Boom "Up/Down" for the wrecker boom operation. This control knob will work on most light duty wreckers by Miller Industries. To see which specific models this knob will fit please see Features below. To view the part schematics click on the Brochure tab.

This Super Oilite Bushing from Miller Industries is used on the Wheel Lift Assembly of Century Formula 6500/600 Series Wreckers, Century Formula I Wheel Lift 411/611 Wreckers and Challenger 4700 Series Wreckers. See the attached brochures. This part can be used to replace Part Numbers: 12-0301583, 12-0301845, 12-0301382, and 12-0302093.

This Thrust Washer from Miller Industries has a diameter of 10" and a thickness of 1/16". It is used on many different Miller wrecker assemblies, including, SDU, LDU, Underlift, and Tower assemblies on Century, Challenger, and Holmes wreckers. Please see the brochure tab for a list of breakdowns.

This is a replacement 17 gallon per minute pump used on carriers by Miller Industries. This pump has a 1" shaft and has 15 splines. It also has a 4 bolt flange.

This is a Miller Industries Long Control Handle for a Car Carrier. It is the rear outer handle on a 5 spool system.

This Bearing Pad from Miller Industries is used on the outer boom of wheel lift and slide-in tire restraint assemblies of Miller Car Carriers. These include Century, Challenger, Champion, Holmes, and Vulcan Carriers. The Bearing Pad measures 6-3/8" long, 4" tall, and 3/8" thick. Please see the brochure tab for a list of breakdowns.

This Miller Industries part is a 7/16" lynch pin for connecting removable rails. It is also used in various other areas.

This is a Miller Industries Long Control Handle for a Car Carrier. It is the rear inner handle on a 5 spool system.