Miller Industries

This 4-Drawer Toolbox from Miller Industries has been specifically designed to be installed in the Century and Vulcan Heavy Duty Modular Aluminum Wreckers. The toolbox is 14" tall, 22" wide, and 17" deep. Get a 3-Drawer Toolbox,

This left hand end plate from Miller industries is used on the outer crosstube assembly on various equipment from Miller Industries. This L-arm bracket is used on the new style "Pivot-L" crosstubes. This bracket attaches to the end of the crosstube to allow your L-arm to pivot.

This is a color control handle kit by Miller Industries. This kit includes enough colored handles to do both sides of a large unit from a 4024 through a 6-winch rotator.

Bolt on striker pin for new style striker type paddle latch

This Cable Tensioner Assembly from Miller Industries is used on H-400 Ramsey Winch. This assembly is used on a Century 10 Series Car Carriers. Please see the brochure tab for a breakdown.

These 7.25" Medium Round Axle Forks from Miller Industries are used to pick up the axle or frame of a truck. They have a 7.25" wide opening, 2" diameter shaft, and 6.5" between the fork holder and the bottom of the cutout.

This LED Flashing Warning Door Light Kit from Miller Industries can be used on Heavy Duty Wrecker Doors. The kit can be wired into the toolbox light switch and give visibility to the toolbox door when opened. The kit includes up to eight lights, four per side, on the vertical doors only.

This Red LED Marker Light from Miller Industries is used on Century, Century LCG, Champion, and Vulcan Car Carriers. The light measures 5-1/2" long and 1" wide. It also comes with a gasket, pigtail and bulb.

The Century trailer ball adapter kit is designed for Century car carriers that have the ear welded on the back side of the crossbar. The kit includes a 2" ball and a wrench for installing and removing ball.

This is a Car Carrier Approach Plate Kit from Miller Industries. It comes with four plates, and all of the hardware to attach. This hardware includes bolts, nuts and washers. The kit is used on aluminum or steel car carriers and it makes it easier to replace worn or broken chain tie downs.

This 49" long stainless steel hinge is used on the 49" aluminum toolbox assembly of Chevron Car Carriers. These include Chevron 16, 20 and 30 Series Car Carriers. The hinge is used with the 49" Toolbox

These Spreader Bar Storage Brackets From Miller Industries are a great way to store you spreader bar on the top of your body side on a heavy duty wrecker. Sold as Pair.

This right hand end plate from Miller industries is used on the outer crosstube assembly on various equipment from Miller Industries. This L-arm bracket is used on the new style "Pivot-L" crosstubes. This bracket attaches to the end of the crosstube to allow your L-arm to pivot.

These Car Carrier Pylons are used with Miller Century, Champion, Challenger, Holmes, and Vulcan Rollbacks. They fit 20 and 30 LCG Series beds. These deck mounted light pylons come in a variety of heights from 48" to 68". Car Carrier Pylons are commonly used as cab protectors. See application chart under the brochures tab.

This heavy duty wrecker lift fork kit includes 9 sets of cast forks. This is the towing fork kit which comes standard when purchasing a new Century or Vulcan Heavy Duty Wrecker. It provides all the towing fork attachments you need for most towing applications. This kit also includes a set of fork spacers which creates a tighter fit and helps eliminate the forks sliding along the truck axle.

Note: Special Handling Fees Apply

<span style="color: red;"/><span style="color: red;"/>Note: Special Handling Fees Apply

</span/>

</span/>

Wheel Grid assembly, left hand, fits Vulcan 850 & 890 wheel lifts. Uses <a href="http://zips.com/parts-detail/miller-l-arm-wheel-retainer-vulcan-850- 8501000" target="_blank"/>8501000</a/> L-arm. This part can be used to replace Part Number, 8500400.

• Fits on 4" x 4" square tube
• Vulcan patented strapless system
• 6,000lbs lift rating

Store your forks with this Fork Holder Storage Kit. This storage kit can be used on a 36" OR 48" Tunnel Box.

Note: Special Handling Fees Apply

This 3.5" Crossbar from Miller Industries is used in the wheel lift and slide-in tire restraint assembly of Century, Century LCG, Champion, and Vulcan Car Carriers. The crossbar uses a 3.5" x 3.5" square tube and has a built in trailer ball plate. Please see the brochure tab for a list of breakdowns.

<pre/>Fits:

2005-Current Century 10 Series Steel & Aluminum Carriers

2005-Current Century 15 Series Steel & Aluminum Carriers

2009-2014 Century LCG 16 Series Steel & Aluminum Carriers

2005-Current Champion Steel & Aluminum 19'-21' Carriers

2005-Current Vulcan 10 Series Steel & Aluminum Carriers

2005-Current Vulcan 10 Series Extreme Angle Steel Carriers

</pre/>

This is a cable tensioner kit for DP winches with a 13-3/4" wide drum.

Note: Special Handling Fees Apply

This is a Miller Industries full bed lock assembly. It includes everything to assemble the weldment (12-0809181), hold downs (12-0809182), mounting brackets (12-0809183), and fasteners of the bed lock. See features for different models of carriers this part applies to. This part can be used to replace Part Numbers: 12-0801209 and 12-0805054.

• Replaces part number: 12-0801205, 12-0801206
• Century/ Vulcan 10 Series 2005-Current
• Century/ Vulcan 15 Series 2005-Current
• Also replaces Assembly 12-0805054

Increase your wreckers storage capacity with this Three-Drawer Tool Storage Box from Miller Industries. The unit is specifically designed to be installed on Century and Vulcan heavy-duty wrecker modular aluminum bodies. The box can be mated with the Miller Four-Drawer Tool Storage Box (Part No.

This cabinet by Miller Industries features seven drawers, an upper compartment designed to hold a rugged, removable carrying case for the operator's air fittings and other miscellaneous items, and a top bolt on tray. Each of the drawers is mounted on a ball bearing 250lb. track system that features a one hand-locking bar. Also included are 12 adjustable dividers that can be used to customize each drawer. The box includes adjustable mounting legs that ease in the installation in the integrated or rotator body.

Miller Chain Storage Rack for Heavy Duty Wreckers. Fits all Vertical Compartments on Century & Vulcan Integrated and Rotator Wrecker Body Sides.

Miller Industries SHORT Spreader Bar. Includes the short tube only. Allows for 58", 63" and 68" Lengths. Spreader Bar Ends sold separately.