Miller Industries

This is a 2 Groove small sheave for the hydraulic hoses on the outer stinger weldment for a Vulcan 807/810, Century 300 Series, and Holmes 440SL by Miller Industries. See brochures for reference chart and see Features for related parts.

Note: Special Handling Fees Apply

Note: Truck Freight Ship Direct Only

• Used in the middle of 21' - 22' beds

Banjo Eyes provide Additional Tie Down Points

This Spreader Bar Rigging Kit by Miller Industries will insure you have the correct rigging to use with the Miller 20 Ton Spreader Bar Kit. This kit includes (3) 1.5" Crosby Screw Pin Shackles, (2) 1.25" Screw Pin Shackles, (2) 5' Orange Endless Loop Straps, and (2) 10' Blue Endless Loop Straps. This kit will accommodate the rigging of one spreader bar.

Note: Special Handling Fees Apply

This crossbar from Miller Industries can be used on Chevron Series 16, Series 20, Series 14, and Series 10 Carriers, as well as Chevron 408V/408T Renegade, 408, 408A, 410, 410A, and 512 Wreckers. It can also be used on Century LCG Generation II 16 Series Steel and Aluminum Carriers made from 2014 until now.

• 2" Center Pin (Not Included)
• Used with Century and Chevron Wheel Lifts
• Length: 56.2"
• Width: 3.5"
• Height: 9"
  
  Fits:
  
  
• Chevron 10, 14, 16, and 20 Series Carriers
• Chevron 408V/408T Renegade Wreckers
• Chevron 408, 408A, 410, 410A, and 512 Series Wreckers
• 2014-Current Century LCG Generation II 16 Series Steel & Aluminum Carriers

These Miller riser brackets can be used on the Vulcan V30, Century 3212, and a Holmes 600R 16 Ton Wreckers. These risers are 7" that are mainly used when extra height clearance is needed for towing.

This is an angle iron used to bear all the control rods and to keep them in line on light duty wreckers by Miller Industries. See Features for related wreckers and Brochures for reference charts.

Miller offset fork adapter for 3.5" x 4" crossbars. This fork adapter is commonly used on Vulcan V30 Wreckers.

Note: Special Handling Fees Apply

This is a Bearing Pad Kit by Miller Industries. It includes all the parts necessary to replace the wear pads on a 10 and 12 Series Steel LCG Car Carrier. See Features for a list of parts that are included.

• (2) 12-0308927-16 5/16"x16" LCG Subframe Bearing Pads
• (2) 12-0308927-66 5/16"x66" LCG Subframe Bearing Pads
• (2) 12-0308927-96 5/16"x96" LCG Subframe Bearing Pads
• (38) 12-0403114 1/4-20x1"x82 Deg Torx Scres
• (2) 12-0306009 5/16"x1 1/4"x60" Bearing Pads

This Mud Flap Bracket from Miller Industries is used on the Control Station Components Assembly of Century LCG 12 and 16 Series Car Carriers. Please see the brochure tab for breakdowns. This part can be used to replace Part Number 12-0704771.

42" Aluminum Tubular Pylon, Optional Light Pylon on Century 3212, Century 3212 CX2, Vulcan VX2, and Vulcan V30-VX body. Requires Work Lights and Signals to Be in the Light Bar.

This is a C-channel end iron used to bear all the control rods and to keep them in line on light duty wreckers by Miller Industries. See Features for related wreckers and Brochures for reference charts.

This Reese Receiver Wheel Lift Adapter from Miller Industries is used on Car Carriers. This removable adapter is specifically designed to be mounted on Miller's Century, Champion, Chevron and Vulcan conventional Car Carrier Wheel Lifts, which have the built-in ball hitch receiver. This 2" universal receiver accepts and pintle or ball hitch with a 2" tube. It is accepted on 10 Series, 12 Series LCG and 16 Series LCG GEN1 built before Sept. 2016 standard wheel lifts. All of the mounting hardware is included on this adapter. For a complete Pintle Hook Receiver Kit see part # ZP-CC-PHK. This part can be used to replace Part Number 12-0809073.

Miller Industries snatch block storage racks for heavy duty wrecker lines. The storage kits allow the hook to be at the top for easier placement of the block in the storage compartments. These storage racks are offered in 3 size formats including a dual, quad and pod box for rotators. The pod box systems store up to 8 snatch blocks.

1/2" grade 100 chain sling foundry hook set. Includes 2 Screw Pin Shackles.

Note: Special Handling Fees Apply

Also know as: wheel grid, slide bar, or Outer Crosstube, this outer crosstube assembly, right hand, fits Century Formula I, Holmes DFT-400. Accepts part# 12-0903479 standard 3500lbs l-arm. This part can be used to replace Part Number 12-0800913.

• Fits 3" x 3" square tube
• Century standard slide in L-arm style
• Fits Century Formula I
• Fits Holmes DFT-400
• Fits Century/Champion 10 Series Carriers

Miller Industries 36" Toolbox Shelf for 36" Tunnel Toolbox (124004137) on Aluminum Heavy Duty Wrecker Body.

Option of driver or passenger side pivot-style l-arm receiver bracket from Miller Industries attackes to the outer crosstubes on Vulcan 870 Series light-duty wrecker wheel lift assebmlies. Also known as a wheel retainer and tire restraint, the L-Arm slides into the angled opening, and the desired position is secured with the bottom side locking pin. This scoop bracket weldment includes the swivel locking pin and the comfort grip stop pin.

This Cable Tensioner Spring from Miller Industries is used on the Cable Tensioner Assembly of a standard 4-Ton Winch. This assembly can be found on a Century, Champion, and Vulcan Car Carriers. See the features below for a full list of carriers and see the brochure tab for breakdowns.

This is a wheel spacer weldment for the L-Arm on the wheel lift of a Holmes 440SL or Vulcan 807 by Miller Industries. This spacer can also be called a tire adapter. This spacer slides onto the end of each L-Arm. It is used when the vehicle you have to tow has low tire pressure or even no tire. This spacer will take up some of the room where the tire would normally rest allowing for a secure hook-up and tow. To view related parts see Features below. To view part schematics click on the Brochures tab.

Miller dual bonded hose is 180" long and fits on the new style Miller carriers with dual hose trays.

Miller Industries Mounting Pin for the Heavy Duty D-Ring (Part #12-0719585) Used On Century, Vulcan, & Challenger Integrated and Rotator Heavy Duty Wreckers.

This is the boom pivot pin for a Vulcan 880/890 Series by Miller Industries. See Brochures for a reference chart and features for related parts.

A 13-3/4" half round rub bar on the tensioner plate for DP winches.

This 9" x 3" x 7/16" Outer Boom Slide Pad from Miller Industries is used on the Boom Assembly of Miller Wreckers. These include Century and Challenger Wreckers. See the features below for a list of trucks and see the brochure tab for breakdowns.