Miller Industries

This is a Seal Kit for the boom lift cylinder on Century 300 Express Series, Century 211 & 212, Challenger 4300 Express Series, and Champion Model 101 Wreckers by Miller Industries. To view part schematics please click on the Brochures tab.

This is a replacement o ring for 9018399.

This passenger side pivot-style L-Arm receiver bracket from Miller Industries attaches to the outer crosstubes on Vulcan 850 and 890 Series light-duty wrecker wheel lift assemblies. Also known as a wheel retainer and tire restraint, the L-Arm slides into the angled opening, and the desired position is secured with the bottom side locking pin. This scoop bracket weldment includes the swivel locking pin but does not include the stop pin.

This Bell Crank from Miller Industries is used on the Winch Clutch Control assembly of several Miller Car Carriers. These include Century, Champion, and Vulcan Car Carriers. See the features below for a list of carriers that this bracket fits, and see the brochure tab for breakdowns.

This is the upper parallel arm of a formula I Wheel Lift mounted to a wrecker by Miller Industries. This part can be used to replace Part Numbers: 12-0801157, 12-0900883, and 12-0800627.

This Transport Tie-Down Kit from Miller Industries comes with all the necessary equipment you need to tie down a load. The kit comes with 5/16" and 3/8" Grade 70 Chains, as well as 1/2" Grade 80 Chains, and two load binders. All of the chains in this kit have a rating tag,

This is a control lever on light duty wreckers by Miller Industries. It is a universal control rod for light duty wreckers and is bare metal (no coating). See Features for related wreckers and Brochures for reference charts.

Note: Special Handling Fees Apply

Outer Crosstube assembly, left hand, New style "Pivot-L" with line-up pin, fits Century Formula 6000 & 6500 and Holmes DFT-650 wheel lifts. Accepts 12-0904156 light weight aluminum L-arm. This part can be used to replace Part Number 12-0902790.

• Fits 3 1/2" x 3 1/2" square tube
• Century new style "Pivot-L" with line-up pin
• Uses 12-0902382 basket strap
• Can also be used on Century/Champion 20 series car carriers

This is a wear pad cage plate on the inside, bottom of the outer boom of a Century Formula I 411/412, and a Century 6500 600 Series Wrecker. This cage plate also fits Challenger 4700 and 4800 Series Wreckers. It will also fit Holmes 440 Series and HP552 Series by Miller industries. See Brochures for a reference chart and Features for related parts. This part can be used to replace Part Number 12-0703093.

This is a multi-position pin.

This Trailer Hitch Adapter from Miller Industries is used on a Century Formula I Wheel Lift that was made after March of 1996. It allows you to tow a trailer with a ball type hitch behind your wheel lift. The Hitch installs quickly and it is small enough to fit in your tool box when it is not being used. Also fits a Holmes DFT-400 and Challenger I-400 Wheel Lift.

Vulcan replacement left hand scoop bracket weldment.

This Vulcan Retaining Pin fits a 896 or 897 model. The function of this retaining pin is to hold on the extension tube and also to prevent the wheel grid from being pulled off the end of the crossbeam.

This is a Bearing Pad Kit by Miller Industries. It includes all the parts necessary to replace the wear pads on a 21'6" & 22'2" Stee l Car Carrier. See Features for a list of parts that are included.

33" Tall Aluminum Light Pylon from Miller Industries. Installation Includes a plastic isolator between the pylon and the body. This light pylon fits on Chevy 3500's without tunnel toolbox, For F-350 through F-450's without tunnel toolbox, and Dodge 3500 through 5500 without tuneel toolbox. This part can be used to replace Part Number 124002343.

This is a Miller pin, hitch.

This is a wear pad retainer plate on the up/down portion of the wheel lift by Miller Industries. It is bolted on by 3 bolts. This retainer plate fits the following wreckers: Vulcan 880/890, Modular 880/890, and 896/897. See Features for related hardware and Brochures for reference charts.

This is a replacement shaft that attaches the boom end sheave to the boom end swivel weldment on Century and Challenger heavy duty wreckers by Miller Industries. This is the shaft the sheave spins on while the winch cable goes in or out. To see which models this shaft fits see Features below. To view the part schematics click on the Brochure tab.

A 12" half round rub bar on the tensioner plate for DP Model # 52864 winches and other DP winches with a 12" wide drum.

The small size and fully waterproof design makes the Dominator Series the versatile answer to all your secondary warning and signaling needs. This light is compact enough for special use vehicles, motorcycles, quads and marine applications. This small but powerful light is the solution to your unique warning light requirements. This light has white and amber flashing lightheads. This light is also ran off of a 12 Volt DC power source.

A 14-1/2" half round rub bar on the tensioner plate for DP winches.

This is a replacement Miller rotator choker and store kit.

This pivot-style L-Arm from Miller Industries fits Formula 6500 wheel lifts on Century wreckers. Also known as a tire restraint or wheel retainer, option of driver or passenger side L-Arm fits 2 x 3 outer crosstubes (Part Nos. 12-0904158 and 12-0904189). This zinc-plated L-Arm also features an alignment hole on the underside and includes a ratchet tie-down strap.