Miller Industries

A cable tensioner kit for DP winches with a 14-1/2" wide drum.

This Transport Chain Kit from Miller Industries can help you with all of your tie-down needs. This kit comes with a variety of 5/16" and 3/8" Grade 70 chains with two lever binders.

This MatJack high pressure kit is designed to lift the heavy weight found on overturned tractor trailers, vehicles stuck in the ditch, and other challenging recoveries. The air bags help to provide access during a recovery or tow when there would otherwise be no space to get a strap under the load. The air bags operate off the service air found on the back of a wrecker and can lift up to 32 tons with a push of a button. These kits are ideal when outfitting all heavy-duty wreckers. MatJack's have been in the towing industry since 1981 and are made in the USA!

These are towbar adapters that fit on the crossbar of a Chevron Autogrip wrecker by Miller Industries. These specialty attachments allow for proffessional and easy hookups when towing wrecked vehicles or trucks with steel bumpers. These adapters are sold as a pair and Chains are not included.

This is the 1/8" thick boom pivot pin shim for a Vulcan Modular 880/890 Series by Miller Industries. See Brochures for a reference chart and features for related parts.

This replacement Curved Axle Fork Set from Miller Industries features a short front lead fork to easily fit under an axle. The rounded inner design fits nicely around the axle.

This driver side pivot-style L-Arm receiver bracket from Miller Industries attaches to the outer crosstubes on Vulcan 850 and 890 Series light-duty wrecker wheel lift assemblies. Also known as a wheel retainer and tire restraint, the L-Arm slides into the angled opening, and the desired position is secured with the bottom side locking pin. This scoop bracket weldment includes the swivel locking pin but does not include the stop pin.

This is an inner tube slide pad for the bottom side of the wheel lift on Century, Vulcan, & Champion car carriers excluding the LCG Series. See Features for which years/models they are used on.

These Low Profile Fork Holders are designed to fit a 4" x 4" crossbar. They are made from the same special cast alloy material as the other Miller products . This fork holder set includes the right and left hand sides.

This is a dual control cable clevis for light duty wreckers by Miller Industries. See Features for related wreckers and Brochures for reference charts.

This seal kit is designed to withstand the temperatures and pressures of hydraulic cylinders and can help operators get the maximum productivity out of their machine. Resealing cylinders is one way to help lower operating costs and improve the performance of your machines hydraulic system. Please remember that seal kits may fit different cylinders of the same diameter.

This 2" x 2" L-Arm Storage Tube from Miller Industries is used on the assembly of Century 10, 15 and 20 Series car carriers. Also for tire restraints and wheel retainers, this bracket can be used on the assembly of newer Champion carriers as well. The tube comes with a camlock built into the back side of it. This part can be used to replace Part Number 12-0802663.

This Stainless Steel Cylinder Wrap Kit from Miller Industries is to be used on Century 9055 and 1140 trucks. The kit will include enough products to do up to 2 cylinder wraps.

This is the 5/64" thick boom pivot pin shim for a Vulcan 880/890 Series by Miller Industries. See Brochures for a reference chart and features for related parts.

To secure exotic and low-profile cars, Miller Industries introduced the Miller Pro Pack Four-Wheel Tie-Down Kit. The kit includes straps that pass through the rims, and is the preferred method of most towers who haul high-end vehicles. This kit was designed specifically for Miller Industries and includes four ratchet assemblies with chain tails, four wheel straps and four fleece sleeve protectors with foam padding and VelcroT closures. A small duffel bag is also included for protecting and storing the components when not in use. The duffel and the straps are all embossed with the Miller Industries logo. This kit provides a fast, safe and convenient way to provide a four-point tie-down while still protecting the finish on expensive rims.

This stainless steel Trim Cover, from Miller Industries, is for each end of the H-Beam Outriggers. This will work with the present outriggers witht he horseshoe on the outside.

This is a LCG carrier control light mounting bracket from Miller Industries.

This is a blade rail used in mids of 17.5' - 20.5' by Miller Industries.

This 49" Long Aluminum Hinge is used on the 49" Toolbox Assembly of Chevron Car Carriers. These include Chevron 16, 20 and 30 Series Car Carriers. The hinge is used with the 49" Toolbox

Note: Due to size of product, additional handling charges may apply.

This Under Body LED Strip Light Kit from Miller Industries comes with a set of six Strip Lights.

This Fold Down Light Bracket for steel Pylons is from Miller Industries. When your light bar height is preventing you from entering parking ramps or garages, the fold down light bracket will provide the solution. This bracket bolts to your light pylon and light bar and allows the operator to pull a spring loaded rod to release the hinged bracket and tip the light bar backwards for additional clearance.

This Clutch Spring from Miller Industries is used on the assembly of 4-Ton Hydraulic Winches. This winch assembly is used on several Miller Car Carriers, including Century, Challenger, Champion, Holmes, and Vulcan Carriers. See the features below for a full list of carriers. Also see the brochure tab for a list of breakdowns.

These Seamless Toolbox Mats by Miller Industries are a great addition to your toolbox to get that great custom look. Not only do they look amazing but they are also very functional. These mats will help keep your towing tools and accessories from sliding around and scratching and damaging the inside of your toolbox. These mats are 12.5' long by 4' wide and are available in 5 different colors. They are available in: Black, Blue, Yellow, Red, and Green.

The "Ground Penetrating Plate" Is Designed To Be Used On Front Foot of Rotators or XPs, and On The Rear Spades Of Century Integrated and HD Fixed-Boom Units. The Sole Purpose Of The Single Pad Is To Dig Into Asphalt, Ice, Etc. Field Testing Has Proven It To Be A Valuable Tool In These Conditions.