Miller Industries

This is a Miller Industries Pintle Hook and Fifth Wheel Adapter Kit. It is designed specifically for Miller 16 ton wreckers including the Vulcan V-30, Century 3212, Vulcan V-24 and Holmes 600R. It fits a 3" x 4" crossbar.

Top wear pads for the underlift of a Vulcan V60 or V70 wrecker.

Note: Special Handling Fees Apply for Specific Items

These Stainless Steel Door Guard Kits are from Miller. They are designed for a Century Box.

Note: Special Handling Fees Apply for Specific Items

This Stainless Steel Door Trim Kit from Miller Industries is used with a Century 3212, CXVX, or V30. Comes with two pieces of trim and a roll of adhesive to attach with.

Available in the following sizes

Item #	Size
124004574	V30-Tall-120"
124004575	V30-Tall-138"
124002613	CXVX/3212/V30 - 3 Door - 120"
124004761	CXVX/3212/V30 - 3 Door - 138"

Chevron cable tie back spring for Chevron 408/410 wreckers.

Bolt on Banjo Eyes make it easier to replace worn or broken chain tie downs. Used on aluminum or steel car carrier beds.

This Winch Clutch Control Assembly from Miller Industries makes reaching your Carrier Clutch Release easier than ever. It is used in the assembly of a Vulcan 10 Series Steel & Aluminum Car Carrier made after 2005. Please see the brochure tab for a breakdown.

This Right Hand Mud Flap Mounting Bracket from Miller Industries is used on the assembly of several Miller Car Carriers. These include Century, Champion, and Vulcan Carriers. Please see the features below for a list of carriers, and see the brochure tab for breakdowns. This part can be used to replace Part Number 12-0704950.

This Shackle Hanger Kit from Miller Industries will Bolt On where you need it. This kit includes 5 hangers that bolt up to a flat surface to hang your shackles on.

This 7/8" premium marine grade hose is sold per foot. When used to wrap the wiring on a carrier approximately 6-1/2' are needed for that application.

A replacement reflector has a STL Body and Slider.

This is a replacement wheel lift extend cylinder shaft on LCG car carriers by Miller Industries. This is the shaft attaches the base end of the cylinder to the wheel lift outer boom weldment. To view specific models see Features below. To view the part schematics see the Brochure tab.

This King Pin Tow Plate Recovery Loop from Miller Industries was designed to be attached to the fifth-wheel pin on a large trailer so that it can be towed without the presence of a tractor. Slide the plate on to the pin, attach your chains, secure them to your sling and lift. Use your safety chains anytime you are towing for maximum security and safety. This part has replaced part number 124001674.

This is a Miller Industries bed lock hold-down for Century/Vulcan car carriers. See features for different models this part applies to. Refer to bed lock assembly 12-0940171 and 12-0905078.

This Telescoping Ladder from Miller Industries is easy to store, transport and maneuver. The telescoping mechanism adjusts the ladders height up to 12.5' and the intelligent design allows for safe, effortless single person operation. This part can be used to replace Part Number 124004413.

Control Rod Lever for Miller Wrecker Models. Fits all Century 200 Series, Holmes 550-2, 440-1 and 440-2, Century 411, 412, 611, 612, 601, 602, 712, 716, 211,311,312, Challenger 4700 and 4800 series wreckers with one piece bodies Takes knob kit 12-0901425 for dual winch wreckers and 12-0901426 for single winch wrecker.

This is a replacement control light used on the LCG Generation 2 Car Carriers.

Stainless Steel Door Guard Kit for Tunnel on Century Large Wrecker.

This Spreader Bar Storage Kit allows you to securely store your end caps for your spreader bar. It will help you prevent misplacing your end caps, and helps protects them from damage while heading out to a recovery scene.

Note: Special Handling Fees Apply for Specific Items<br //><br //>

This is a stainless steel tail light mounting plate for car carriers. It is for the right hand side of the tail light assembly. The mounting holes are cut out vertically, to allow your tail lights to be mounted vertically. This part can be used to replace Part Number 12-0720031.

Safety Chain Roller Kit for All Large Miller Wrecker Bodies Excluding Rotators.

This T Handle from Miller Industries is used in the Winch Clutch Control assembly of several Miller car Carriers. These include Century, Challenger, Champion, Holmes, and Vulcan Carriers. See the features below for a full list of carriers. Also see the brochure tab for a list of breakdowns.

This is a wheel lift wear pad for the lower tilt column on Holmes and Vulcan Wreckers. This wear pad will fit on the following wrecker models: Holmes 600R, Vulcan 880/890, Modular 880/890, 896/897. See Brochures for reference charts.