Cylinder and Pin Replacement

This is the Swing L-Arm Cylinder, also known as the Claw Cylinder, for autoload wreckers by Miller Industries. This cylinder will fit Century Express 300 Series, Midnight Express Series, Challenger 4300 Express Series, Holmes 440SL, Vulcan Modular 807, 810 Intruder and 810 Power Tilt Wreckers. To view part schematics click the Brochures tab.

This is the rear extend cylinder pin for many light duty wreckers by Miller Industries. This pin will work with most Century, Challenger, Champion, Holmes and Vulcan light duty wreckers. This pin measure 6" long with a diamter of 7/8". To view specific wrecker models this pin fits see Features below.

This is the L-Arm side, Swing L-Arm Cylinder Pin. This pin fits cylinder part number 12-0303844. This pin fits Century, Challenger and Vulcan wrecker models. To view specific models see Features below. To view part schematics click on the Brochures tab.

This is the front extend cylinder pin for the wheel lift extend cylinder on Miller Industries Light Duty Wreckers. It replaced part number 12-0703345. To view what models this pin fits on please see Features below. To view part schematics click on the Brochures tab.

This 12-004086 Seal Kit fits 10 Series Century, Holmes, Champion Wheel-lift In/Out Cylinders using a 0302178 Cylinder 2.5" x 60" to 12/2002. This seal kit will also fit wheel lift extend cylinder, 12-0303020, on Century, Challenger, Champion, and Holmes Light Duty Wrecker Models. Please remember that seal kits may fit different cylinders of the same diameter. See the chart below for more information.

This is a replacement seal kit for the swing L-arm cylinder for autoload wreckers by Miller Industries. This seal kit if for cylinder part number: 12-0303844.

This is the Wheel Lift Extend Cylinder on Light Duty Wreckers by Miller Industries. This extend cylinder will fit on the following models. The Century 300 Express Series, The Century 300 Modular Express Series, The Challenger 4300 Express Series, The Holmes 440SL Series, The Vulcan Modular 807, The Vulcan 810 Intruder, The Vulcan 812 Intruder, and The Vulcan 810 Power Tilt. To view part schematics click the Brochure Tab.

This is a Seal Kit for the Boom Lift Cylinder on Century and Holmes Light Duty Wreckers by Miller Industries. This seal kit will fit the lift cylinder on Century Formula I Duplex Tilt 411 & 412, and Holmes HP 552 / DFT 650. To view part schematics click on the Brochures tab.

This seal kit is designed to withstand the temperatures and pressures of hydraulic cylinders and can help operators get the maximum productivity out of their machine. Resealing cylinders is one way to help lower operating costs and improve the performance of your machines hydraulic system. This cylinder fits the wheel-lift lift cylinder used on both car carriers and light duty wreckers. See Features below to view specific models of each. To view part schematics click the Brochures tab. Please remember that seal kits may fit different cylinders of the same diameter. See the chart below for more information.

This is the clevis pin for the Swing L-Arm cylinder on the Century Express 300 Series, Holmes 440SL and the Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This clevis pin measures 5/8" x 1.5". This pin is used to connect the swing L-arm cylinder to the swing L-arm. To see which specific models this pin fits please see Features below. To view part schematics click on the Brochure tab.

This is the Seal Kit for the Boom Extend Cylinder on Miller Light Duty Wreckers. This seal kit is for cylinder part number 12-0301755. To view what models this will fit see Features below. To view part schematics click the Brochures tab.

This is a Pin that is used in different locations on the Wheel Lift of Century Formula I Duplex Tilt 411 & 412, and Holmes 440 Series / DFT 400 light Duty wreckers by Miller Industries. This pin is used to hold the tilt cylinders on to the wheel lift frame weldment. This pin also is used to attach the upper arm weldments to the wheel lift frame weldment also. To view part schematics click on the Brochure tab.

This is a replacement auto grip claw cylinder for second generation auto grip autoloaders, 2003 and up. Right hand claw cylinder. This is the cylinder that moves your right wheel retainer on your wheel lift.

This is a 1" Snap Ring by Miller Industries. This snap ring is used on the wheel lift extend cylinder pin. This snap ring secures the pin in place. To view the part schematic click on the Brochure tab.

Replacement Auto Grip Claw Cylinder for Chevron second generation 2003 and up. Left hand claw cylinder.

This is a replacement Seal Kit for Wheel Lift Fold Cylinder 12-0302919.

This is the weldment pin that connects the outer stinger to the parallel arms on a Formula I 411/412 by Miller Indstries. See brochure for reference chart.

This is the Wheel Lift Extend Cylinder Base End Pin for Century Modular Midnight Express and Modular 211's. This pin also will fit Holmes 440SL, Vulcan Modular 804, 806, and 807 wreckers. It will also work with the Vulcan 810 Power Tilt light duty wrecker by Miller Industries. To view specific models see Features below. To view part schematics click the Brochure tab.

Note: Special Handling Fees Apply

This is the Lift Cylinder on the Wheel Lift of Century Wreckers with the Formula I and Formula 6500 Wheel Lifts. It is used on the Century Formula 6500 - 600 Series and the Modular 400 & 600 Series with these wheel lift options. To view part schematics click the Brochure tab.

• Uses holding valve part number 12-0304567
  
  Fits:
• Century Formula 6500, 600 Series REV A
• Century Modular 400 & 600 (01/2009 - Current)

This is the base lift cylinder pin on the wheel lift of Century, Challenger and Holmes wreckers by Miller Industries. This pin replaces part number 12-0801012. This cylinder pin will fit the following wreckers: Century Formula I - Duplex Tilt 411 & 412, Formula I - Duplex Tilt Super Six & 500, Formula 6000 - 600 Series, Formula 6500 - 600 Series, Metro I - Duplex Tilt, Challenger 4700 Series, and the Holmes 440 Series. To view year ranges see Features below. To view part schematics click on the Brochures tab.

This is a replacement wheel lift upper arm pin weldment on Light Duty Century and Holmes Wreckers by Miller Industries. This pin attaches the wheel lift upper arm weldment to the outer boom weldment of the wheel lift. This pin fits the Century Formula 6500, 600 Series and Modular 400 & 600 Series. It will also fit the Holmes HP 552/DFT 650 wrecker. To view the part schematics please click the Brochures tab.

This is a 1/4" x 1-3/4" Roll Pin that is used to secure the Swing L-Arm Pin on a Vulcan Modular 807 light duty wrecker by Miller Industries. To view the part schematic click on the Brochure tab.

This is a 2.5" Wheel Lift Fold Cylinder on Century Modular Midnight Express, Holmes 440SL and Vulcan 810 Intruder light duty wreckers. To view specific wrecker models please see Features below. To view part schematics click on the Brochure tab. This part can be used to replace Part Number, 810700000.

This is the Wheel Lift Extend Cylinder Pin for the wheel lift of many light duty wreckers by Miller Industries. This extend cylinder pin fits the following wreckers: Century Modular 300 Express Series, Century Modular Midnight Express, Century Modular 211, Holmes 440SL, Vulcan Modular 804, 806, and 807, and the Vulcan 810 Power Tilt. This pin measures 5.88" long with a diameter of 7/8". To view specific models and year range for each model see Features below.

This is the Wrecker Boom Lift Cylinder on the Holmes 440SL, Vulcan 810 Intruder, Vulcan 812 Intruder, and the Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This cylinder has a 3.5" bore with a 10.44" stroke. This lift cylinder connects to the subframe weldment and to the outer wrecker boom weldment. This is the cylinder that raises the boom of the wrecker up and down. This lift cylinder is also referred to as the boom elevation cylinder. To see which specific models this cylinder will fit please see Features below. To view part schematics click on the Brochure tab.

This is a replacement wheel lift upper arm pin weldment on Light Duty Century and Holmes Wreckers by Miller Industries. This pin attaches the wheel lift upper arm weldment to the frame weldment. This pin fits the Century Formula 6500, 600 Series and Modular 400 & 600 Series. It will also fit the Holmes HP 552/DFT 650 wrecker. To view the part schematics please click the Brochures tab.

This is the seal kit for the wheel lift tilt cylinder on the Century Formula 6500 - 600 Series light duty wrecker by Miller Industries. To view part schematic click on the Brochure tab.

Note: Special Handling Fees Apply

This is the extend cylinder for the wheel lift on Miller Industries Light Duty Wreckers. This will fit the Century EB4 Express, Century Formula I 411 & 412, Century Formula I Super Six & 500 Series, Century Formula II, Century Formula 6000 - 600 Series, Century Metro I, Century Modular 211, Century Modular 400 & 600, Century 211 & 212. It will also fit the Challenger 4700 Series, Champion Model 101, Holmes 440 Series, Vulcan Modular 804, and Vulcan Modular 806. To view specific years of wrecker models see Features below. To view part schematics click on the Brochures tab.

Dimensions: 39"L x 5"W x 5"H

Length Eye to Eye: 37.5" L
Fits:

Century EB4 Express (03/1999 to Current)

Century Formula I, Duplex Tilt, 411 & 412 Wreckers

Century Formula I, Duplex Tilt, Super Six & 500 Series

Century Formula II

Century Formula 6000, 600 Series

Century Metro I, Duplex Tilt (D.T.) Wheel Lift System

Century Modular 211 (02/2010 to Current)

Century Modular 400 & 600 (01/2009 - Current)

Century 211 & 212 (11/1997 to Current)

Challenger 4700 Series (02/1995 - Current)

Champion Model 101 (09/1994 - Current)

Holmes 440 Series / DFT 400 (10/1994 - Current)

Vulcan Modular 804 (02/2010 - Current)

Vulcan Modular 806 (02/2010 - Current)

This is the Wheel Lift Extend Cylinder Rear Pin for the Vulcan 800 Series light duty wreckers by Miller Industries. This includes the 880 / 890 Series, Modular 880 / 890 Series and the 896 / 897 Series. This pin is used to connect the wheel lift extend cylinder to the wheel lift inner boom weldment. To see which specific wrecker models this pin fits please see Features below. To view the part schematics click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder Pin for the Holmes 440 Series / DFT 400 light duty wreckers by Miller Industries. This pin goes through the rod end of the cylinder. This pin attaches the tilt cylinder to the outer wheel lift boom. To view the part schematic click on the Brochure tab. This part can be used to replace Part Number 12-0801010.

This is the Wrecker Boom Lift Cylinder Pin for the Holmes 440SL, Vulcan 805, and Vulcan 810 Series light duty wreckers by Miller Industries. This pin goes through the base end of the lift cylinder. This pin connects the boom lift cylinder to the subframe weldment. To view part schematics click on the Brochure tab.

This is the Lift Cylinder Pin on the Wheel Lift for Century Formula 6500 - 600 Series and Century Modular 400 & 600 Light Duty Wreckers by Miller Industries. This is the pin for the rod end of the lift cylinder. To view specific models this pin will fit see Features below. To view part schematics click the Brochure tab.

This is the fold cylinder lower pin on the wrecker boom of the Century Midnight Express and Vulcan 807 by Miller Industries. See Brochures for reference chart and Features for related parts.

This is the Wheel Lift Tilt Cylinder Pin for the Vulcan 810 Power Tilt light duty wrecker by Miller Industries. This pin goes through the base end of the tilt cylinder. This pin attaches the tilt cylinder to the wrecker outer boom weldment. To view the part schematic click on the Brochure tab.

This is the stinger pivot pin on the wrecker boom of the Century 211/212/300 Series by Miller Industries. See Brochures for reference chart and Features for related parts.

This is a pivot pin for the Boom Extend Cylinder on many Miller Industries Light Duty Wreckers. This pin fits the Century 300 Express Series, Century Formula 6000 - 600 Series, Century Formula 6500 - 600 Series, Century Modular 400 & 600, Challenger 4300 Express Series, Challenger 4700 Series, Challenger 4800 Series, Eagle EB-3 Series, Holmes 440 Series, Holmes HP 552 & DFT 650, Vulcan Modular 806, 807, 880/890 wreckers. See Features below to view models this pin fits. To view part schematics click on the Brochures tab.

This Extend Cylinder Outer Boom Shaft from Miller Industries is used on many different assemblies on Century, Challenger, Holmes, and Vulcan Wreckers. These assemblies include boom, front outrigger, and wrecker assemblies. Please view the brochures tab to see a full list of wrecker assemblies and parts schematics.

This is the Wheel Lift Tilt Cylinder Lower Pin on the Vulcan 880 / 890 Series and the Vulcan 896 / 897 Series light duty wreckers by Miller Industries. This pin is also used to attach the wrecker boom lift cylinder to the subframe weldment on the Vulcan 896 / 897 Series wrecker. To see which specific wrecker models this pin will fit please see Features below. To view the part schematics click on the Brochure tab.

This is the Wheel Lift Fold Cylinder for the Wheel Lift on the Vulcan 812 Intruder and Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This cylinder has a 4" bore with a 19.5" stroke. This cylinder attaches to the wrecker outer boom weldment and to the wheel lift outer boom weldment. This is the cylinder that folds the wheel lift up against the boom of the wrecker for travel. To see which specific wrecker models this cylinder will fit please see Features below. To view the part schematics click on the Brochure tab.

This is a multi-position pin.

This is the Seal Kit for the Lift Cylinder on the Wheel Lift of a Challenger 4700 Series and a Holmes 440 Series / DFT 400 light duty wrecker by Miller Industries. This seal kit is used on lift cylinder part number 12-0302341. To view part schematics click on the Brochure tab.

This is a Seal Kit for the boom lift cylinder on Century 300 Express Series, Century 211 & 212, Challenger 4300 Express Series, and Champion Model 101 Wreckers by Miller Industries. To view part schematics please click on the Brochures tab.

This Lower-Tilt Cylinder Shaft is used on Boom and Underlift Assembly of Light Duty Wreckers from Miller. These include Century, Challenger, Champion and Eagle Wreckers. Please see the features below for a list of wreckers and see the brochure tab for breakdown schematics.

This is the Upper Pin for the Wheel Lift Tilt Cylinder on Century Modular Midnight Express, Holmes 440SL and Vulcan 810 Intruder light duty wreckers by Miller Industries. This pin is used to connect the tilt cylinder to the subframe assembly. To view the specific wrecker models see Features below. To view part schematics click on the Brochures tab.

This is the Wheel Lift Extend Cylinder Pin for the Century Modular 400 & 600 Series and the 614 Formula IIT light duty wreckers by Miller Industries. This pin is for the rod end of the extend cylinder. To see which wrecker models this pin will fit please see Features below. To view part schematics click on the Brochure tab.

This is the Seal Kit for the Lift Cylinder on the wheel lift of the Century Formula 6500 - 600 Series and Holmes 552 / DFT 650 light duty wreckers by Miller Industries. The part number for the lift cylinder is 12-0303065. To see which specific models this seal kit fits please see Features below. To view part schematics click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder on Century, Challenger, and Holmes Light Duty Wreckers. This cylinder will fit Century Formula I Duplex Tilt 411, 412, Super Six and 500 Series wreckers. It will also fit the Century Formula 6000 - 600 Series, Metro I - Duplex Tilt, Modular 400 and 600 Series. It fits the Challenger 4700 Series and the Holmes 440 Series. This tilt cylinder can be used on both the left and the right side of the wheel lift. This cylinder replaces part numbers: 12-0302905, 12-0302904, 12-0303674, and 12-0303675. To view specific wrecker models this cylinder fits see Features below. To view part schematics click the Brochures tab.

This is the Wheel Lift Tilt Cylinder Lower Pin for the Vulcan 810 Intruder light duty wrecker by Miller Industries. This pin goes through the rod end of the tilt cylinder. This pin attaches the wheel lift tilt cylinder to the wheel lift outer boom weldment. To view the part schematic click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder Upper Pin on the Wheel Lift of a Century Modular 400 & 600 Series, Vulcan 880/890, Vulcan Modular 880/890 and the Vulcan 896/897 Series light duty wreckers by Miller Industries. This pin connects the wheel lift's tilt cylinder to the wheel lift frame weldment. To view which wrecker models this pin fits please see Features below. To view part schematics click on the Brochure tab.

This is the Wheel Lift Tilt Cylinder for the Vulcan 880 / 890 Series light duty wreckers by Miller Industries. This cylinder allows your wheel lift to tilt up and down. This cylinder connects to the wheel lift tilt column and the subframe of the wrecker. To view the part schematic click on the Brochure tab.

This is a seal kit for the boom lift cylinder on Century Light Duty Wreckers by Miller Industries. This seal kit will fit the Century Formula I Duplex Tilt Super Six and 500 Series, and The Formula 6000 - 600 Series. To view part schematics click on the Brochures tab.

Note: Special Handling Fees Apply

This hydraulic wheel lift up/down cylinder is designed to withstand necessary forces and to be used at stated pressures. It meets industry and government specifications and will prove itself on the job when it really matters. This cylinder has a 4" bore. This cylinder will work with wheel lift applications on both car carriers and light duty wreckers by Miller Industries. This cylinder is designed to be used on 1989 - 1997 Formula I and WL-300 equipment without a valve. This lift cylinder fits Miller 10 Series Carriers from 2001 to Current and Standard and Right Approach 10 Series Carriers. This cylinder will also fit Challenger 4700 Series, Holmes 440 Series/ DFT 400, and Holmes HP 552 / DFT 650 Series light duty wreckers. Standard cylinder color is black. To view part schematics click on the Brochure tab.

• This Homac cylinder is designed to be used on 1989 - 1997 Formula 1 and WL-300 equipment without a valve
• Replaces 12-0301484
• Seal Kit # 12-03000017
  
  Fits:
• Miller 10 Series Carrier 02/2001 to Current
• Standard and Right Approach 10 Series Carriers
• Fits Challenger 4700 Series (02/1995 - Current)
• Fits Holmes 440 Series / DFT 400 (10/1994 - Current)
• Fits Holmes HP 552 / DFT 650 (09/1994 - Current)

This is the Boom Lift Cylinder Lower Pin for a Century 400 & 600, Vulcan 880/890 and Vulcan Modular 880/890 light duty wrecker by Miller Industries. This pin connects the lift cylinder to the subframe for the wrecker. To see which specific wrecker models this pin will fit please see Features below. To view part schematics click on the Brochure tab.

This hydraulic wheel lift lift cylinder is designed to withstand necessary forces and to be used at stated pressures. It meets industry and government specifications and will prove itself on the job when it really matters. Standard cylinder color is black. This tilt cylinder will fit both car carriers and light duty wreckers. It will fit Gen II 10 Series Miller Carriers, which includes Century, Holmes, Vulcan, Champion and Challenger including Right Approach Models.

This is the Fold Cylinder Upper Pin for the base end of the cylinder on Century Modular 211, Vulcan Modular 804, Modular 806 and Modular 807 light duty wreckers by Miller Industries. This is the pin that connects the fold cylinder to the boom of the wrecker. To see which specific models this pin will fit please see Features below. To view part schematics click on the Brochure tab.

This is a Miller cylinder, 812 claw. generation 3.

This is the Wheel Lift Tilt Cylinder Lower Pin for the Vulcan 812 Intruder and the Vulcan 810 Power Tilt light duty wreckers by Miller Industries. This pin goes through the rod end of the tilt cylinder. This pin attaches the tilt cylinder to the wheel lift outer boom weldment. To see which specific wrecker models this pin will fit please see Features below. To view the part schematics click on the Brochure tab.

This Cotter Pin from Miller Industries is used on the Winch Clutch Control of 4-Ton Hydraulic Winches,

This is the Lower Cylinder Pin on the Lift Cylinder on Century Formula I Duplex Tilt 411 & 412 wreckers. This pin also fit the Century Formula 6000 - 600 Series wrecker. To view part schematics click on the Brochures tab.